LCD TV
32 VLC 6121 C
EN
Contents--------------------------------------------------------------------------------------------------------------------------------------
48- operAtion-As-A-pC-monitor
48 Connecting a PC
-
48 Selecting presets for the PC
48 Settings for PC mode
49- operAtion-with-A-Common-
interFACe
-
49 What is a Common Interface?
49 Inserting the CA module
49 Access control for CI module and
smart card
50- speCiAl-settinGs
51 Searching for digital terrestrial
TV channels automatically
-
52 Searching for digital terrestrial
TV channels manually
53 Tuning analogue television channels
54 Changing stored analogue channels
56- inFormAtion
-
56 Displaying signal information
56 Service information for retailers
56 Environmental note
57 Technical data
58 Troubleshooting
-3
ENGLISH
setup-AnD-sAFetY-------------------------------------------------------------------------------------------------------
7
Please note the following instructions when
setting up the television set:
Make sure the power cord or the power sup-
ply unit (if provided) are not damaged.
7
7
7
This television is designed to receive and dis-
Only operate the television with the power
supply/power cord provided.
play video and audio signals.
All other uses are expressly prohibited.
Thunderstorms are a danger to all electrical
devices. Even when the television is switched
off, it can be damaged by a lightning strike to
the mains or the antenna. Always disconnect
the mains and antenna plugs during a storm.
7
The ideal viewing distance is five times the
diagonal screen size.
7
Light falling on the screen impairs picture
quality.
7
7
Use a damp, soft cloth to clean the screen.
Do not use water with soap or detergent.
7
To ensure the device is always adequately
ventilated, make sure there is sufficient space
between the television set and nearby furniture
(min 10 cm).
Only clean the housing of your television set
with the cloth provided. Do not use water with
soap or detergent.
7
The television is designed for use in dry rooms.
7
If you do use it outdoors, make sure it is pro-
tected from moisture such as rain or splashing
water.
When deciding where to put the device, re-
member that furniture is often coated with vari-
ous types of varnish and plastic. Many of these
contain chemicals which can corrode the feet
of the device, leaving marks on the surface of
the furniture which can be difficult or impossi-
ble to remove.
Never expose the television set to moisture.
7
Do not place any vessels such as vases on the
television, as they may spill liquid, thus present-
ing a safety risk.
7
The screen of your LCD television meets
the highest quality standards and has been
checked for pixel faults.
Despite the great care taken in manufacturing,
technological reasons make it impossible to
completely discount the possibility that some
pixels may be faulty.
Provided they are within the thresholds speci-
fied by the DIN norm, pixel faults of this kind
cannot be regarded as a defect as defined by
the warranty.
7
Place the television on a hard, level surface.
7
Do not place any objects such as newspapers
on the television or put cloth or similar items
under it.
7
Do not place the television close to heating
units or in direct sunlight, as this will impair
cooling.
7
Heat build-up can be dangerous and shortens
the service life of the television. For reasons of
safety, have a repairman remove any dirt in
the television from time to time.
7
To ensure fires do not occur,
always keep candles and other
open flames away from the device.
7
Never open the television under any circum-
stances. Warranty claims are excluded for
damage resulting from improper handling.
-4
ENGLISH
setup-AnD-sAFetY-------------------------------------------------------------------------------------------------------
7
Do not connect any other equipment while the
device is switched on. Also switch off other
equipment before connecting it.
7
Do not plug in the power cord of the device
until you have connected the external equip-
ment and the antenna.
7
To avoid safety problems arising from the bat-
teries used with the product, follow the instruc-
tions below.
7
In case of misplacement of batteries, they may
cause explosion due to short circuit.
7
Do not expose the batteries to excessive heat
such as direct sunlight, fire, etc.
7
Do not use old and unused batteries together.
7
Only replace the exhausted batteries with
those having the same model, value and prop-
erties.
7
To avoid environmental health problems aris-
ing from the product, batteries and accesso-
ries.
7
Make sure the mains plug is freely accessible.
Caution:
7
If you plan on using a wall bracket for your
television, make sure you read the assembly
manual for the wall bracket or have a spe-
cialist assemble it.
7
When purchasing the wall bracket, make
sure that all the fastening points on the televi-
sion are also on the wall bracket and that
they are all used when mounting it.
-5
ENGLISH
GenerAl-inFormAtion----------------------------------------------------------------------------------
7
Using the time shift function, you can quickly
special-features-of-your-
and easily pause a programme using the re-
-television-set
mote control and resume it at a later stage.
7
You can receive and watch digital TV channels
The programme is recorded in an external
using your television set (via DVB-T and DVB-C)
data medium.
– including High Definition programmes (HD).
7
You can record any digital TV channels you
However, the reception of digital TV channels
choose.
in HD is currently limited to a few countries in
The TV channels are converted by the televi-
Europe.
sion and saved on an external data medium
7
Although this television set complies with the
current DVB-T and DVB-C standards (status:
which is connected to the USB socket.
The saved programmes can be called up and
August 2010), the compatibility with future ter-
played from the archive on the external data
restrial DVB-T and DVB-C cable programmes
medium at any time.
cannot be guaranteed.
You can also play a programme from the
archive while recording another.
More information on recording and playing
TV programmes can be found on page 24.
7
Your television set can receive and process
all analogue and non-encrypted digital
TV channels. The television set is also equipped
with digital and analogue receivers.
7
The electronic TV guide (for digital channels
only) informs you about any schedule changes
at short notice, and provides an overview of
all the broadcasters' schedules for the next few
days. Detailed information on the individual
television programmes are – when provided
by the broadcasting station – are also avail-
able in the electronic TV guide.
7
You can connect various data media, such as
an external hard drive, a USB memory stick or
a digital camera, to the USB socket. Using the
file browser, you can then select and play the
file formats of your choice (for example, MP4,
MP3 or JPEG data).
-6
ENGLISH
GenerAl-inFormAtion----------------------------------------------------------------------------------
receiving-digital-channels
You require a digital roof antenna or indoor
antenna (passive or active indoor antenna
with its own power supply) to receive digital
television channels (DVB-T).
important-notes-on-
7
environmental-protection
7
The following information will help you to save
resources – and money as well.
7
If you are not using your television set for
7
If you wish to receive digital television chan-
several days, you should pull out the mains
plug for environmental and safety reasons.
This way the television does not consume any
electricity.
nels via your cable system (DVB-C), the an-
tenna cable for your cable operator must be
connected to the television set.
7
Unlike analogue broadcasting, not every
7
As switching off the television set does not
channel has its own transmission frequency.
Instead, several channels are grouped into
what are known as bouquets on a regional or
national level. You can find the current trans-
mission information on teletext from various
broadcasters, or by consulting a current TV
guide or the Internet.
completely disconnect it from the mains, pull
out the plug to disconnect it from the mains
completely.
7
If the device is equipped with a power switch,
switching it off using this switch will be suffi-
cient. The energy consumed by the television
set is reduced to virtually 0 W.
7
Various digital television channels from private
7
In standby mode, the television set uses very
broadcasters are encrypted (DVB-T and DVB-
C). Watching these channels and the record-
ing and playback functions are only possible
with the appropriate CI module and a Smart-
Card. Ask your specialist dealer.
little energy. However, it may be necessary to
leave the television set in standby mode for cer-
tain functions (for example automatic switch-on
and switch-off and for timer functions).
The range of channels available from the pub-
lic broadcasting institutions (ARD with EinsEx-
tra, EinsFestival or ZDF with ZDF Info and all
third party broadcasters) are not encrypted
and can be received without a SmartCard.
7
The television set uses less energy when the
brightness is reduced.
-7
ENGLISH
ConneCtion-AnD-prepArAtion------------------------------------------------
Connecting-the-antenna-and-power-cord
2
1
1a To receive terrestrial digital broadcasters
(DVB-T) connect the cable for the rooftop
or indoor antenna (passive or active indoor
antenna with its own power supply) to the an-
tenna socket »Ant-in« on the television set;
2
Plug the power cord into a wall socket.
note:
7
Do not plug in the power cord of the device
until you have connected the external equip-
ment and the antenna.
or
7
Only use the power cord supplied to connect
1b To receive digital cable channels (DVB-C)
connect the cable for the rooftop antenna
to the antenna socket »Ant- in« on the
television set;
the television set to a suitable earthed safety
socket.
7
Do not use an adapter plug or extension
lead which does not meet the applicable
safety standards. Do not tamper with the
power cord.
or
1c To receive analogue TV channels, connect
the cable for the rooftop antenna to the an-
tenna socket »Ant-in« on the television set
note:
7
When connecting an indoor antenna you
may have to try it out at different positions
until you get the best reception.
-8
ENGLISH
ConneCtion-AnD-prepArAtion------------------------------------------------
environmental-note
inserting-batteries-into-the-
-remote-control
7
This symbol on recharge-
able batteries/batteries
or on the packaging indi-
cates that the rechargea-
ble battery/battery may not be disposed of
with regular household rubbish. For certain
rechargeable batteries/batteries, this sym-
bol may be supplemented by a chemical
symbol. Symbols for mercury (Hg) or lead
(Pb) are provided if the rechargeable batter-
ies/batteries contain more than 0.0005%
mercury or more than 0.004% lead.
Rechargeable batteries/batteries, including
those which do not contain heavy metal,
may not be disposed of with household
waste. Always dispose of used batteries
in accordance with local environmental
regulations. Make enquiries about the appli-
cable disposal regulations where you live.
1
2
Open the battery compartment by removing
the lid.
Insert the batteries (2 x 1.5 V micro, for
example R03 or AAA). Observe the po-
larity marked in the bottom of the battery
compartment.
3
Close the battery compartment.
note:-
7
If the television no longer reacts properly
to remote control commands, the batteries
may be flat. Always remove used batteries.
7
The manufacturer accepts no liability for
damage caused by leaking batteries.
-9
ENGLISH
overview-------------------------------------------------------------------------------------------------------------------------------------
Connections-on-the-television-set
Av1-/-s-vhs
SCART socket (CVBS signal,
RGB signal);
Video and sound socket for
S-Video camcorder.
optic-out
Socket for audio output
(optical) for PCM/AC3
signals.
For connecting digital AV
amplifiers or AV receivers.
Component
Audio
pC-in
Socket for audio
input for a PC.
---pb-pr-Y/Av2 Sockets for video input
(YUV signal).
l--r
Sockets for audio input
VGA socket, video input
for PC.
(YUV signal);
Audio socket for
camcorder.
Ant-in
Antenna socket for a DVB-T,
DVB-C and analogue
antenna.
Y/Av2-
-Video socket for
camcorder
-10
ENGLISH
overview-------------------------------------------------------------------------------------------------------------------------------------
hDmi2
hDmi3
U
HDMI socket,
Controls-on-the-television-set
audio/video input.
8/i-
Switches the television on and
back into standby mode.
HDMI socket,
audio/video input.
v–--v+
menu-
Adjusts the volume;
Headphone jack (3.5 mm
jack plug);
Sockets for audio output.
selects menu functions.
-Opens the menu.
Select a menu option with
»p+« or »p–«.
usB
-USB socket for external
data media without a power
supply of their own and
PVR function.
Activate the function with
»v+«.
Confirm the function with
»v+« or »v–«..
hDmi1
Ci- -
HDMI socket,
audio/video input.
Press »menu« to quit the menu.
sourCe- Opens the pre-selection for
AV channels.
-Common Interface Slot.
In the menu, press »p+« or »p–«
to select and press »sourCe« to
confirm.
p–--p+
Switches the television on from
standby;
selects channels in steps;
selects function in the menu.
-11
ENGLISH
overview-------------------------------------------------------------------------------------------------------------------------------------
the-remote-control-–-main-functions
Switches on from standby;
Selects channel – directly
Switches on and off
(Standby).
Selects the channel list
(»All«, »FAV 1« to »FAV 4«).
Switches between
teletext and TV mode.
Opens the selection menu to
change picture formats.
Opens the »HDMI CEC De-
vice List«.
Then select with » « or » «
<
>
and press »oK« to confirm.
Displays information.
-Zapping function;
switches back one menu
level in the menus.
Opens the main menu
-Opens the channel list.
Opens the electronic
TV guide.
Opens the TOOLS menu.
Adjusts the volume.
Opens menu for AV channels
and USB input.
Then select using »
v«, » «,
<
» « or » « and press »oK«
Λ
>
to confirm.
Muting
Switches on from standby;
Selects channel – in steps.
Record, play, pause and
stop (only digital television
channels - to/from external
USB device).
Opens the »PRnP« menu.
navigation-in-the-menus
-
and down in the menus.
-
right in the menus.
-Activates various functions and
save functions/settings.
-12
ENGLISH
overview-------------------------------------------------------------------------------------------------------------------------------------
the-remote-control-–--
All-functions
Selects different subtitles
(only for digital television chan-
nels)
» «-(red)-
Selects pages in teletext;
Selects/activates various
Selects different audio lan-
guages (only for digital televi-
sion channels)
»
»
»
« (green)
« (yellow) functions in the menus.
« (blue)
Starts the recording (
digital television channels
recording is made on an exter-
nal data medium).
only for
, the
8
Starts playing a programme
from an external data medium;
Repeats a recorded pro-
gramme.
!
Freeze frame, if no external
data medium is connected;
Playback pause;
Time shift mode (only for digital
television channels and when
an external data medium is
connected).
7
5
Ends playback of a pro-
gramme from an external data
medium;
Ends a recording or
playback in time shift mode;
Splits the screen in teletext.
Switches to double character
size in teletext;
Selects the next title/next pic-
ture in the file browser.
6
Refreshes a teletext page;
Selects the previous track/pre-
vious picture in the file browser.
3
Stops scrolling through pages
in teletext;
Starts a fast reverse search in
the file browser.
4
Reveals answers in teletext;
Starts a fast forward search in
the file browser.
-13
ENGLISH
settinGs------------------------------------------------------------------------------------------------------------------------------------------
selecting-language,-country-and-
operating-mode
initial-set-up-and-tuning-
-television-channels
The television set is equipped with automatic
channel search, which searches for terrestrial
channels (DVB-T), cable channels (DVB-C) and
analogue channels.
1
Switch on the television set from standby with
»8«, »1…0« or »p+« or »p-«.
– During initial set-up, the »Installation Guide«
will be displayed.
You start the search and can then copy the tel-
evision channels into four favourite lists and sort
them there into your order of preference.
help:-
7
If this menu is not displayed, restore the
television set to its default settings (see
page 41).
For DVB-T and DVB-C channels 1000 presets,
and 100 presets for analogue channels.
2- Select the menu language with » «, » «,
<
>
»v« or »
Λ« and press »oK« to confirm.
the-various-settings
3- Select the mode with » « or » « and press
<
>
Depending on the type of antenna connected,
you can decide which channels you would like
the television to search for.
»oK« to confirm.
– The settings used in »Home Mode« help to
save energy.
7
Tunes digital terrestrial television channels, on
page 15.
– Alternatively, the menu item »Shop Mode«
can be selected which the retailer can use
for demonstrating the device functions.
7
Tunes digital television channels from the
cable provider, on page 15.
note:
7
End the »Shop Mode« by restoring the tel-
7
Tunes analogue television channels, in the
evision set to its default settings (see page
41).
chapter “Special functions”, starting on page
53.
4- Select the country in which the television set
7
Further settings for digital television channels
is operated with » «, » «, »v« or »Λ« and
<
>
after the initial set-up can also be found in the
chapter “Special functions”, starting on page
50.
press »oK« to confirm.
– The »Source Setup« menu appears with the
»Connection Type« line marked.
note:-
note:
7
Make the language and country selection for
all types, then continue reading the respective
chapter.
7
You can find a description of how to tune
the television channel of your choice – de-
pending on the antenna connected – in the
following chapters.
-14
ENGLISH
settinGs------------------------------------------------------------------------------------------------------------------------------------------
tuning-terrestrial-television-
channels-(DvB-t)
tuning-television-channels-from-
the-cable-provider-(DvB-C)
1
In the »Source Setup« menu, in the »Connec-
tion Type« line, select the option »Cable«
with » « or » «.
1
In the »Source Setup« menu, in the »Connec-
tion Type« line, select the option »Air« with
» « or » «.
<
>
<
>
2
Select the line »Scan Type« with »
«.
Use » « or » « to set the required scan
v« or
2
Select the line »Scan Type« with »
«.
Use » « or » « to set the required scan
v« or
»Λ
»Λ
<
>
<
>
type:
type:
– »DTV«, scan for digital television channels;
– »ATV«, scan for analogue television
channels;
– »DTV«, scan for digital television channels;
– »ATV«, scan for analogue television
channels;
–
»ATV & DTV«, scan for analogue and
digital television channels.
–
»ATV & DTV«, scan for analogue and
digital television channels.
3
Select the line »Cabel Scan Type« with »
or » «. Select the preferred option (»Quick«
or »Full«) with » « or » «.
– The search function »Quick« sets up the
channels according to the information pro-
vided by your cable provider in the trans-
mission signal.
v«
Caution:
Λ
7
The antenna power supply (5V ) may only
<
>
be switched on if the antenna is an active
indoor antenna with a signal amplifier and it
is not already supplied with a voltage via a
mains plug (or similar supply). Otherwise
you may cause a short circuit and irrepara-
bly damage your antenna.
– If the option »Full« is selected, the entire
frequency range will be scanned. The
search can take a long time with this op-
tion. This option is recommended if your
cable provider does not support the scan
3
4
Select the line »Active Antenna Power« with
»
v
«
or »Λ«.
Switch on the antenna power supply for the
antenna with » « or » « (»On«).
<
>
type
»Quick«.
Start the scan with » « (green).
note:
– The »Search Results« menu appears, and
the search for TV channels begins.
– Depending on the number of television
channels received, this can easily take a
few minutes.
7
You can accelerate the search. To do this,
you need information about the frequency
and network ID. You are usually able to get
this data from your cable operator or find it
in forums on the Internet.
– The scan is complete as soon as the »PRO-
GRAM TABLE« appears.
4
Start the scan with » « (green).
–
The »Search Results« menu appears, and
the search for TV channels begins.
note:
7
You can abort the scan by pressing
»menu«.
– Depending on the number of television
channels received, this can easily take a
few minutes.
– The scan is complete as soon as the »PRO-
GRAM TABLE« appears.
5
Press »menu« to end the setting.
note:
7
You can abort the scan by pressing
»menu«.
5
Press »menu« to end the setting.
-15
ENGLISH
settinGs------------------------------------------------------------------------------------------------------------------------------------------
selecting-channel-lists
Changing-the-program-table-for-
the-digital-channels
1
Open the menu with »menu«.
Channels which are found using the scan are
saved in the »PROGRAM TABLE«.
2
Select the »SOURCE SETUP« menu with »v«
or »Λ« and press »oK« to confirm.
– The »SOURCE SETUP« menu appears.
You can delete channels which are not required
from the programe table, and lock individual
channels (Parental control).
3
Select the line »Programe Table« with »v«
or »Λ« and press »oK« to confirm.
– The menu »PROGRAM TABLE« appears.
You can also add channels to the favourites list;
in addition, you can change the order of chan-
nels within the favourites list.
important:
7
Programe table and favourites lists are
saved separately according to the different
input sources (cable and air).
With » « (green) you can display the channels
which belong to one network.
7
When opening the programme table, the
respective channel list for the current input
signal appears.
Switch to the next page in the programe table
with »p+« and to the previous page with »p-«.
With »
« (yellow) you can open the »LIST
note:
MANAGEMENT« within the programe table.
In this List Management you can create your
own favourites lists.
7
If in the Program Table
appears added
to the name of the channel, you need a
CI module and a Smart-Card for watching
these channals.
INSTALLATION
PROGRAM TABLE
Network ALL
1
Das Erste
Service
ALL
DTV
RADIO
DATA
ATV
2
ZDF
3
SAT1
4
N24
3sat
5
SAT3
1 Das Erste
DTV
DTV
DTV
DTV
DTV
6
24
7
HD Sport
8
HD Test
9
10 RTL
DTV
DTV
DTV
DTV
DTV
11 HD 1
12 Life
13 Film
14 Promo
15 Sport1
DTV
DTV
DTV
DTV
DTV
16 TV Sport
17 Sat.8
18 SKY
19 TV6
20 TV5
DTV
DTV
DTV
DTV
DTV
Edit
Network
Manage lists
Sorting
Exit
Select favourites
Back
-16
ENGLISH
settinGs------------------------------------------------------------------------------------------------------------------------------------------
notes:
Creating-lists-of-favourites
You can save your favourite channels in up to
four favourites lists (FAV 1 to FAV 4).
7
Repeat steps 2 and 3 if you would like to
change other channels within the same
favourites list.
notes:
7
Repeat steps 1 to 3 if you would like to
change channels in a different favourites list.
7
Favourites lists must be created separately
for all input sources (cable and air).
4
Exit the current favourites list with »
(blue).
– The entire programe table will appear
again.
«
7
You can select the favourites list by pressing
»FAv«.
1
2
3
In the »PROGRAM TABLE« menu, switch over
to the list view with » « (yellow).
Deleting-channels
1
Select the channel of your choice with »
or »Λ«.
v«
In the »PROGRAM TABLE« menu, select the
television channel to be deleted with «,
» « or » « and press » «- (red) to
»
v
“Push” the channel into the favourites
»
Λ«,
<
>
lists 1 to 4 with » « or » « and press »oK«
<
>
activate.
to confirm.
– The position in the favourites list is marked
with »✔«.
2
3
4
Deletethecurrentchannelwith» «(yellow);
« (blue).
delete all channels with »
– You can enter the same channel in more
than one favourite list.
– Each favourite list can store up to 255
channels.
Confirm the deletion process with »
(green).
«
Quit the deletion process with » «.
<
note:
skipping-channels
You can mark television channels which should
be skipped when selecting with » « or » «.
It is still possible to select them using the number
buttons.
7
Channels can also be deleted from the
favourites lists. Select the channel to be
Λ
v
deleted with »
v«, »Λ«, » « or » « and
<
>
press »oK« to delete it.
7
When deleting a channel from the favourites
list, the order within the favourites list will be
updated.
1
2
3
In the »PROGRAM TABLE« menu, switch over
to the list view with » « (yellow).
Select the preferred channel with »
or » «.
v«
4
Press »menu« to end the set-up.
Λ
sorting-channels-in-the-favourite-list
You can change the order of channels in the
favourites list.
Select the column »Skip« with » « or » «
and use »oK« to mark the channel.
– The channel is marked by »✔«.
<
>
1
In the »PROGRAM TABLE« menu, select the
favourites list »1« to »4«.
note:
7
Channels can also be reactivated. Select the
channel with » « or » «, then select the
column »Skip« and reactivate the channel
with »oK«
2- Select the channel which should be moved
with » «, » «, » « or » « and mark it with
» «-(red).
v
Λ
v
Λ
<
>
.
3
Move the channel to its new position with
«, » «, » « or » « and press »oK« to
confirm.
»
v
Λ
<
>
-17
ENGLISH
settinGs------------------------------------------------------------------------------------------------------------------------------------------
notes:
picture-settings-
7
You can only select the »Mpeg NR« function
1
Open the menu with »menu«.
on digital and AV presets.
2
Select the menu item »PICTURE SETTINGS«
»Mpeg NR« reduces any interference from
artefacts (pixel blocks) from digital pro-
grammes due to MPEG compression (such
as from DVB-T receivers or DVD players).
The »Film Mode« detects and processes
feature films automatically for all channel
sources. This means you will always receive
an optimal picture.
This functions in the modi 480i, 576i and
1080i in TV playback and for other channel
sources.
If the »Film mode« is switched on for pro-
grammes without a feature film signal, minor
problems such as picture freeze, defective
subtitles or fine lines in the picture could
occur.
The function »Dynamic Contrast« adapts the
contrast dynamically and optimally for the
respective picture content.
With »Dynamic Backlight«, the device opti-
mally adapts the background lighting to the
picture content.
The »Backlight« can only be set manually
when the function »Dynamic Backlight« is
deactivated.
»MEMC« will only appear in menus of LCD
products with 200 Hz PPR Feature and LED
products with 400 Hz PPR feature..
with »v« or »Λ« and press »oK« to confirm.
– The »PICTURE SETTINGS« menu appears.
20.09.2010
15:46
PICTURE SETTINGS
7
Picture Mode
Brightness
Contrast
User
50
100
Sharpness
Colour
75
65
Colour Temperature
Medium
Enhanced picture settings
DNR
Off
Off
7
7
7
7
Mpeg NR.
Exit
Back
3
Select the line »Picture Mode«, »Bright-
ness«, »Contrast«, »Sharpness«, »Colour«, or
»Colour Temperature« with »v« or »Λ«.
Select the value with » « or » « and press
<
>
»oK« to confirm.
notes:
7
When changing the values with » « or
<
5
Press »menu« to end the setting.
» «, the screen will be split. You can see
>
the current setting on the left side, the new
setting on the right side.
7
In the »PICTURE SETTINGS« menu you can
also find other additional settings.
4
Select the line »DNR«, »Mpeg NR«, »Vibrant
Colour«, »Perfect Clear«, »Film Mode«,
»Gamma«, »Dynamic Contrast«, »Dynamic
Backlight«, »Backlight« or »MEMC« with
»
v« or »Λ«.
Select the value with » « or » « and press
<
>
»oK« to confirm.
-18
ENGLISH
settinGs------------------------------------------------------------------------------------------------------------------------------------------
Automatic-volume
sound-settings-
Television stations broadcast at different vol-
umes. The automatic volume limiting (AVL) func-
tion means the volume is kept the same when
you switch between channels.
1
Open the menu with »menu«.
2
Select the menu item »SOUND SETTINGS«
with »v« or »Λ« and press »oK« to confirm.
– The »SOUND SETTINGS« menu appears.
1
Select the line »AVL« with »
v« or »Λ« and
20.09.2010
15:46
select the option »On« with » « or » «.
<
>
SOUND SETTINGS
note:
7
If the »SRS TS HD« setting has been selected
in the »Audio Mode« line, the AVL line can-
not be selected.
Volume
10
Balance
AVL
Off
stereo/two-channel-sound,-mono
Sound Type
Sound Mode
Stereo
Normal
Speech
If the device receives two-channel-sound pro-
grammes, e.g. a film with the original soundtrack
on audio channel B (display: »Dual II«) and
the dubbed version on sound channel A (dis-
play: »Dual I«), you can select the audio channel
you prefer.
Sound Preset
External connections
Audio Output Setup
Accessibility Settings
If the device receives stereo or Nicam pro-
grammes, it switches automatically to stereo
sound (display: »Stereo«).
End
Back
You can switch the sound to »Mono« if the stereo
sound quality is poor.
note:
1
Select the line »Audio Type« with »
v« or
7
Additional operations are explained in the
following sections.
»Λ
« and adjust the setting with » « or » «.
<
>
stereo-width
volume
This broadens the sound output for stereo pro-
grammes and improves the sound with mono
reception.
1
Select the line »Volume« with »
v
« or »
>
Λ
«
«
and change the setting with » « or » «.
<
Balance
1
1
Select the line »Audio Mode« with »
or » «.
v«
Select the line »Balance« with »
v
« or »
>
Λ
Λ
and change the setting with » « or » «.
<
2
Select the option »Spatial« with » « or » «.
<
>
-19
ENGLISH
settinGs------------------------------------------------------------------------------------------------------------------------------------------
soundeffects
equalizer
This menu offers three preset sound effects
(Music, Natural and Speech) and one setting to
be created by you (User).
Equalizer offers a sound setting that you can cre-
ate.
Equaliser appears in the menu when »Sound
mode« is selected as »Spatial« or »Normal«,
and »Sound Medium« as »User«.
1
Select the line »Sound Preset« with »
v« or
»
Λ«.
1
2
Select »Equalizer« with »v« or »Λ« and
2
Select the sound effect »Music«, »Natural«
or »Speech« by pressing » « or » «.
press »oK« to confirm.
<
>
The »EQUALIZER« menu appears.
note:
note:
7
»User« option is active when »Sound mode«
setting is selected as »Normal or »Spatial«.
7
If the »SRS TS HD« setting has been selected
in the »Sound Mode« line, the »Equalizer«
line will not indicate.
srs-trusurround-hD
SRS TruSurround HD is a patented audio tech-
nology which is integrated into the television set
and only requires the built-in speakers to gener-
ate a Surround Sound effect.
Select the frequency bandwidth »120Hz«
with »v« or »Λ«.
Set the preferred value with » « or » «.
<
>
3
4
Set the next frequency bandwidth with »
or » « and repeat the setting.
v«
1
2
3
4
Select the line »Sound Mode« with »
or » «.
v«
Λ
Λ
Press » « to save the setting.
<
Select the option »SRS TS HD« with » « or
<
Audio-description-(Audio-subtitles)
» «.
>
Audio description is an additional audio channel
for visually-impaired persons. Descriptions are
provided of activities, surroundings, changes of
scene, gestures and actors' facial expressions.
Select the line »SRS Sound Preset« with »
v«
or »Λ«.
Select the sound effect »Music«, »Natural«
or »Speech« with » « or » «.
<
>
This audio channel is transmitted simultaneously
with the normal sound on digital channels. Avail-
ability depends on the respective channel and
broadcaster.
1
Select the line »Audio Description« with »
v
«
or »Λ
« and select the option »On« with » «
<
or » «.
>
2
Select the line »Volume« with »
v
« or »
>
Λ
«
and change the volume with » « or » «.
<
exiting-the-setting
1
Press »menu« to end the setting.
* Under licence from SRS Labs, Inc. TruSurround HD,
SRS and the
symbol are trademarks of
SRS Labs, Inc.
-20
ENGLISH
television---operAtion--------------------------------------------------------------------------------
Displaying-information
Basic-functions
1- Display information with »?«.
– The display disappears automatically after
a short while.
switching-on-and-off
1
Press »8«, »1…0« or »p+« or »p-« to switch
on the television from standby mode.
Freeze-frame
2
Press »8« to switch the television to standby.
If you wish to view a particular scene for longer,
you can “freeze” the frame of the current pro-
gramme.
selecting-channels
1
Press »1…0« to select presets directly.
1
2
Activate the freeze-frame function with »$«.
End the freeze-frame function with »$«.
note:
2
Select channels step by step with »p+« or
»p-«.
3- Open the channel list with »oK«, select the
preferred television channel with » «, » «,
» « or » « and press »oK« to confirm.
7
v
Λ
If an external data medium is connected
to the television, the time shift function is
activated with »$«. The time shift function is
described on page 27.
<
>
Exit the channel list with »menu«.
selecting-channels-from-lists
You can select channels from various lists (e.g.
all channels, FAV 1 to FAV 4).
picture-settings
Various picture settings are available.
1
Press »FAv« to open an overview of pro-
grame tables.
1
2
Open the Tools menu with »tools«.
Select the menu item »Picture Mode« with
– The overview is displayed.
»v« or »Λ«.
2
3
4
Select a channel list with »
Λ« or »v« and
3- Select »User«, »Eco TV«, »Vivid«, »Natural«,
»Movie«, »Sports« or »Game« by pressing
» « or » «.
open it with »oK«
.
Select a television channel with »
v
«, »Λ«,
<
>
» « or » « and press »oK« to confirm.
<
>
note:
Press »menu« to exit the channel list.
7
Picture setting »Game« can only be selected
in »HDMI«, »Component« and »PC« modes.
selecting-a-preset-Av-channel
Audio-settings
Various audio settings are available.
1
Open the »Select Source« menu with »
Select an AV preset with » «, »
» « and press »oK« to confirm.
«.
2
v
Λ«, » « or
<
>
1
2
Open the Tools menu with »tools«.
3
Use »1…0« to switch back to the television
channel.
Select the menu item »Sound Preset« with
»v« or »Λ«.
Adjusting-the-volume
3
Select the audio setting »User«, »Music«,
o
»Natural« or »Speech« by pressing » « or
1
Adjust the volume with »
«.
<
- -–
+
» «.
>
switching-sound-on/off
note:
1
Press » « to mute the sound or switch it
p
on again.
7
»User« option is active when »Sound mode«
setting is selected as »Normal or »Spatial«.
-21
ENGLISH
television---operAtion--------------------------------------------------------------------------------
Audio-language
electronic-tv-guide
Various languages are available on digital tele-
vision channels. This depends on the programme
being broadcast.
The electronic TV guide provides an overview of
all programmes that will be broadcast in the next
week (for digital channels only).
1
2
Open the selection menu with »
«.
1
Press »GuiDe« to display channel informa-
tion.
Select the language by pressing »
and press »oK« to confirm.
v« or »Λ«
notes:
7
Not all channels supply provide a detailed
subtitles
TV guide.
Various subtitles are available on digital televi-
sion channels. This depends on the programme
being broadcast.
7
Many broadcasters transmit the current
schedule, but do not offer detailed descrip-
tions.
1
2
Open the selection menu with » «.
7
There are broadcasters which do not pro-
vide any information at all.
Select the subtitles with »v« or »Λ« and
press »oK« to confirm.
2
3
Press »v« or »Λ« to select a television
channel.
Zoom-function
1
– Today's programmes on the television
channel selected are displayed.
Open the Tools menu with »tools«.
2
Select the menu item »Zoom« with »v« or
Switch to the information about the current
»Λ«.
programme with » «.
>
3- Press- »oK« repeatedly to enlarge the
notes:
display in three steps.
7
You can open and switch off the extensive
programme information with »?«.
eco-mode
This function allows you to reduce the power
consumption.
7
You can can added the selected broadcast
to the memory timer by pressing »oK«
.
4
5
6
Press »
v
« to select information on the next
1
2
Open the Tools menu with »tools«.
Select the menu item »Eco TV« with » « or »Λ«.
programme and, »
Λ
« to return to the infor-
v
mation for the current programme.
3- Switch on the Eco mode with » « or » «.
<
>
Select programmes on over the coming days
with » « (green), and switch back to the cur-
4
Switch the Eco mode off again with » « or » «.
<
>
rent day with » «-(red).
Zapping-function
This function remembers the channel you are
currently watching while you switch over to other
ones (zapping).
Switch back to the channel selection with
» «.
<
note:
7
Filter for certain programmes with »
«
(blue), select the channel type with » «,
1
Press »1…0« or »p+«, »p–« to select the
<
channel to be stored in the zapping memory
» «, »v« or »Λ« and press »oK« to con-
>
and press » « to confirm.
<
firm. Programmes which match the selected
channel type are displayed.
2
3
Press »1…0« or »
Λ«, »v« to switch to
another television channel.
7- Quit the electronic TV guide with »menu«.
Press » « to switch between the saved tel-
<
evision channel and the last television chan-
nel viewed.
4- End the function with »menu«.
-22
ENGLISH
television---operAtion--------------------------------------------------------------------------------
»panorama«-format-
Changing-the-picture-format
This setting is suitable for films in an especially
wide format.
The television automatically switches to the 16:9
format if this format is detected via the SCART
socket.
During programmes in 4:3 format, the picture is
stretched horizontally if the »Panorama« function
is selected. The picture geometry is stretched
horizontally.
1
Select the picture format with » «.
– The picture format (for example »16:9«) is
displayed.
– You can choose between the following
picture formats:
»overscan«-format
In this mode, HD pictures are not cropped by the
HDMI sockets or component sockets, and are
displayed in their original size. This only applies
in HDMI mode and for resolutions of 720p or
above.
»Auto«-format
The picture format is automatically switched to
»16:9« for 16:9 programmes.
The picture format is automatically switched to
»4:3« for 4:3 programmes.
»16:9«-and-»14:9«-formats
For programmes in 4:3 format, the picture is
stretched horizontally if the »16:9« format or
»14:9« format is selected.
The picture geometry is stretched horizontally.
With actual 16:9 input sources (from a set-
top box on the SCART socket) the picture fills
the screen completely and with the correct
geometry.
»4:3«-format
The picture is shown in 4:3 format.
»letterBox«-format-
The letterbox format is especially suitable for
programmes in 16:9 format.
The black borders which are usually at the top
and bottom of the screen are eliminated, 4:3 pic-
tures fill the screen.
The transmitted pictures are enlarged, but are
slightly cropped at the top and bottom. The pic-
ture geometry remains unchanged.
»subtitle«-format
If you cannot see the subtitles at the bottom of
the screen, select »Subtitle«.
-23
ENGLISH
usB-reCorDinG---------------------------------------------------------------------------------------------------------------
possible-limitations-when-using-
an-external-data-medium
Depending on the broadcaster, you may experi-
ence various restrictions on some of the functions
from some television channels.
information-on-recording-and-
playing-television-programmes
Recording and playback of television pro-
grammes is only possible with digital television
channels (DVB-T and DVB-C).
■
■
The digital television channels (DVB-T and
DVB-C) you are able to record and playback
also depends on the broadcaster.
GrunDiG-has-no-influence-on--
these-restrictions.
■
Recording a programme on the external data
■
Recording and playback of programmes,
medium can be disabled by the broadcaster.
If the message »URI* protected! PVR function
is blocked« appears on the screen, then re-
cording or timeshift is restricted (one recording
possible) or disabled (recording not possible)
by the broadcaster.
as well as the time shift function, can only be
carried out using an external data medium
(hard drive or USB stick). The data medium
should have a minimum storage capacity
of 2 GB.
* URI = User right information (Copyright in-
formation).
■
Recordings can be made with most data media
on the market. However, we cannot guarantee
operation for all data media.
■
If you record and save a programme on the
archive of an external data medium, playback
can be restricted.
The broadcaster can allow you to view this
programme one or more times, but it may only
be available for a certain period of time.
■
If a programme was recorded on an external
data medium, it can only be played back on
your television set. The playback of these pro-
grammes is not possible on other devices.
■
If you send your television to be repaired and
■
Programmes not suitable for minors will require
hardware components need to be replaced,
you might not be able to play the recordings
again on the repaired television.
the input of a PIN number immediately before
recording starts. If this authorisation is not
given, the recording may not start.
■
Reception for SKY broadcasting service is cur-
rently only possible in Germany with a suitable
set-top box or suitable CA module.
■
Copying a programme from a digital television
channel onto a video or DVD recorder using
the »Av- 1« socket (analogue picture/
sound signal) can also be restricted by the
broadcaster. Prerequisite is that your device
supports the copying function.
■
Grundig does not accept liability for any loss
of saved data on an external data medium.
-24
ENGLISH
usB-reCorDinG---------------------------------------------------------------------------------------------------------------
notes:
Connecting-external-data-media-
7
If you use a network cable for external hard
notes:
disks which have been connected to the
7
Before connecting the data medium, switch
the television to standby with
the device and then switch the television on
again.
»usB« socket of the television, this network
»8«. Connect
cable must also be disconnected from the
power supply when the television is switched
off.
7
7
Before removing the external data medium,
the television must be switched to standby,
so that no data loss occurs.
7
External data media may not be disconnect-
ed from the television while files on the data
medium are being accessed.
Your television features two USB sockets,
»usB«.
settings-for-usB-recording
selecting-the-menu
»usB« is used to connect data media,
which require an additional power supply
– for example, external hard disks.
1
Open the menu with »menu«.
2
Select the line »USB RECORDING« with
»
v« or »Λ« and press »oK« to confirm.
– The »USB RECORDING« menu appears.
20.09.2010
15:46
USB RECORDING
OK
PRnP
Auto Preview
On
Manage data medium
Safely Remove Disk
Disk
USB
C:
Partition
Capacity Used
%3
1249
Used (MB)
Total (MB)
38145
1
2
Connect the »usB« socket of the television
and the corresponding socket of the data
medium (external hard disk) using a USB ca-
ble;
Remaining SD recording time
Remaining HD recording time
1,008 min
288 min
Exit
Back
or
insert the USB plug of the USB memory stick
into the »usB« socket of the television.
Confirm the display »
(green).
– The file browser appears.
« with »
«
-25
ENGLISH
usB-reCorDinG---------------------------------------------------------------------------------------------------------------
switching-on-automatic-preview
testing-the-external-data-medium
If the automatic preview is switched on, a pre-
view of the selected file appears in the file
browser.
You can subject external data media to a test
and establish whether they are suitable for the
chosen functionality.
1
2
3
Select the line »Auto Preview« with »
«.
v« or
1
2
3
Select the line »Disk« with »v« or »Λ«. If
»Λ
several data media are connected, select the
preferred data medium with » « or » «.
Switch on the function with » « or » «
<
>
« or »
<
>
(»On«).
Select the line »Partition« with »
v
Λ«.
If several partitions are available, select the
partition you wish to use with » « or » «.
Press »menu« to end the setting.
<
>
safely-remove-disk
1
Select the line »Check Disk« with »
v
« or
Select the line »Safely Remove Disk« with
« or » « and press »oK« to confirm.
»
Λ« and press »oK« to confirm.
Information on the data medium is dis-
played.
»v
Λ
–
note:
7
The disk can now be removed from the
socket.
4
Press »menu« to end the setting.
selecting-external-data-media
If several external data media are connected to
the television, you can select the preferred data
medium.
1
2
Select the line »Disk« with »v« or »Λ«
Select the preferred data medium with » «
<
or » «.
>
3
Press »menu« to end the setting.
selecting-a-partition-on-the-external-
data-medium
If the external data medium features several par-
titions, select the partition you would like to use.
1
2
Select the line »Partition« with »v« or »Λ«.
Select the partition you wish to use with » «
<
or » «.
>
3
Press »menu« to end the setting.
-26
ENGLISH
usB-reCorDinG---------------------------------------------------------------------------------------------------------------
″pausing”-time-shift--
programmes
You can pause the programme you are watch-
ing. This is a useful function, for example if the
telephone rings while you are watching a film
and you do not want to miss anything.
recording-programmes
You can record programmes. The data for these
programmes is recorded on an external data
medium and this archive is administered via the
television.
The following approximate values apply for re-
cording:
Recording time for high-definition programmes
(HD) is 7 minutes with 1 GB of memory,
for standard programmes it is 26 minutes.
A freeze-frame display of the last scene appears
on the screen and the programme is recorded
in the time shift memory of the external data
medium.
While recording, you can watch another pro-
gramme from the archive.
In time shift mode you can record a maximum of
20 minutes of the current programme.
You cannot change presets.
1
Press »!« to pause the current programme.
– The picture is frozen, the time shift and the
remaining recording time are displayed.
one-touch-programme-recording
1
Select the television channel to be recorded
2
Press »8« to resume the programme.
with » »1…0« or »p+«, »p–« and press
–
The programme will continue to be
recorded.
»
« to start the recording.
– Information on the recording is displayed:
the recording symbol, the channel name,
the programme, the recording time and the
available memory space.
note:
7
The following functions are possible when in
time shift mode:
– Rewind, press »3« several times accord-
ing to speed (the picture freezes while
rewinding);
– Fast forward, press »4« several times
according to speed;
– Select pause with »!«.
– After a short time this information disap-
pears.
2
3
End the recording with »7«.
Confirm the display with » « (green);
or
3
Press »7« to quit the time shift function.
– The message »Live programme« appears,
and you will see the current programme
without time shift.
press » «-(red) to continue the recording.
notes:
7
After the recording is complete, the record-
– The scenes in the “time shift memory” are
deleted.
ing will be automatically saved on the exter-
nal data medium.
7
The »RECORDED FILES« menu, with the ar-
chived programmes, can be opened with
»reC.list«.
7
If the external data medium is disconnected
from the USB socket during recording, the
recording will be stopped automatically
and will not be saved.
7
Play your recordings, that you have record-
ed with your FAT32 formatted HDDs, in USB
mode.
-27
ENGLISH
usB-reCorDinG---------------------------------------------------------------------------------------------------------------
recording-a-programme-from-the-
channel-list
presetting-programmes-to-be-
recorded
1
Open the »CHANNEL LIST« with »oK«
Select a television channel with » «, »
» « or » « and press »oK« to confirm.
.
...-using-the-electronic-tv-guide
You can use data from the electronic TV guide
for recording.
2
v
Λ«,
<
>
3
4
Press »menu« to exit the channel list.
Press » « to start recording.
25 programmes can be preset for the timer
recording or as a reminder.
– Information on the recording is displayed:
the recording symbol, the channel name,
the programme, the recording time and the
available memory space.
– After a short time this information disap-
pears.
1
Press »GuiDe« to display channel informa-
tion.
– The electronic TV guide appears.
2
3
4
5
Select the preferred channel with »
v«
or »Λ«.
Switch to the information about the current
5
6
Press »7« to stop recording.
programme with » «.
>
Confirm the display with » « (green);
Select the programme of your choice with
or
»
v« or »Λ«.
press » «-(red) to continue the recording.
Confirm the programme with »
«.
– The symbol » « appears after the name
of the programme, and the data has been
added to the timer.
note:
7
If the data for the recording is to be changed,
use
»
« (yellow) and
»
« (blue) to
switch to the »SCHEDULED EVENTS«, press
»
»
«(green),changethedataandsaveitwith
« (green)
.
6
Press »menu« to exit the menu.
notes:
Before the timer recording begins, a warn-
7
ing message appears with a 20-second
countdown. You can switch over to the pro-
grammed television channel.
7
If the timer recording starts during playback,
playback is not interrupted: Recording takes
place automatically in the background as
long as you do not select »Yes« when the
timer countdown message is shown.
-28
ENGLISH
usB-reCorDinG---------------------------------------------------------------------------------------------------------------
...-by-manual-data-entry
You can preset up to 25 programmes for timer
recording.
editing-recording-data-in-the--
timer-menu
You can edit the data for programmed timer
recordings.
1
Press »GuiDe« to display channel informa-
tion.
– The electronic TV guide appears.
1
Select the timer menu by pressing »GuiDe«
sion.
,
»
« (yellow) and « (blue) in succes-
»
2
3
Open the »MAKE SCHEDULE« menu by
– The »SCHEDULED EVENTS« menu ap-
pears.
pressing » « (yellow) twice.
Select the line »Type« with »v« or »Λ«
2
3
Select the title of the programme to be
and select the option »Recording« with » «
<
changed with »
v« or »Λ« and activate the
or » «.
>
timer position with
»
« (green).
– The input menu is displayed.
4
5
Select the line »Channel« with »
v
« or »
>
Λ
«
and select the channel with » « or » «.
<
Select the required option with »
« and edit the data with »1…0« and
» « or » «.
v« or
»Λ
Select the line »Mode« with »v« or »Λ« and
select the preferred mode (»Once«, »Every
Day« or »Weekly«) with » « or » «.
<
>
<
>
4- Save the changes with » « (green).
– The timer has been changed.
6
7
Select the line »Start« (Start recording) with
« or » « and enter the date/time with
»1…0«.
»
v
Λ
5
Press »menu« to close the menu.
Deleting-recording-data-in-the-timer-
menu
You can delete the data for programmed timer
recordings.
Select the line »End« (Stop recording) with
« or » « and enter the date/time with
»1…0«.
»v
Λ
8- Save the data with » « (green).
1
Select the timer menu by pressing »GuiDe«
sion.
,
– The programme is preset.
»
« (yellow) and « (blue) in succes-
»
9
Press »menu« to exit the menu.
notes:
Before the timer recording begins, a warn-
– The »SCHEDULED EVENTS« menu ap-
pears.
7
ing message appears with a 20-second
countdown. You can switch over to the pro-
grammed television channel.
2
3
Select the title of the programme to be deleted
with »
with
v« or »
Λ« and delete the timer position
»
« (yellow)
.
7
If the timer recording starts during playback,
Press »menu« to close the menu.
playback is not interrupted: recording takes
place automatically in the background as
long as you do not select »Yes« when the
timer countdown message is shown.
-29
ENGLISH
usB-reCorDinG---------------------------------------------------------------------------------------------------------------
playback
The recorded programmes – whether started
playback-during-a-recording
During a recording, you can either watch the
manually or using the timer function – are stored
programme you are currently recording or watch
on the external data medium. You can open the
a different one that you have already recorded.
archive on the external data medium by pressing
1
Select the channel to be recorded with
»1…0« or »p+«, »p–« and press »
start the recording.
»reC.list«.
« to
selecting-a-programme-from--
the-archive
2
Select the »Recorded Event« menu by press-
ing »reC.list«.
1
Open the »Recorded Event« menu with
»reC.list«
.
3- Select the programme you want with »
v
« or
– The menu appears.
»
Λ
« and press »8« to start playback.
2
3
Select the programme of your choice with
–
The recording continues in the background.
»
v« or »Λ« and start playback with »8«.
4
5
Press »7« to end playback.
Press »7« to end playback.
– The television switches over to the current
television channel.
Press »7« to stop recording.
Deleting-programmes-in-the-
recording-list
You can delete programmes from the record-
ing list.
Forward/reverse-picture-search
1
During playback, select the fast forward
speed (2x, 4x, 8x, 16x or 32x) with »4«;
or
1
2
Open the »Recorded Event« menu with
»reC.list«
.
during playback, select the rewind speed
(2x, 4x, 8x, 16x or 32x) with »3« (the pic-
ture freezes when rewinding).
– The menu appears.
Select the programme to be deleted with
»
v« or »
Λ«.
repeating-a-scene-(A-B)
You can mark the starting and ending point of a
scene. The scene is then repeated continuously.
3
4
Press »
« (blue) to delete the programme.
Confirm the security query with
»
«
(green)
.
1
Mark the starting point A by pressing »8« at
the required scene during playback.
–
note:
This scene is marked as the starting
point A.
7
You cannot delete programmes in the
»Recorded Event« menu which are currently
being recorded or played back.
2
Mark the end point B by pressing »8«
once again at the required scene during
playback.
5
Press »menu« to close the menu.
– This scene is marked as the end point B.
– The television repeats the programme be-
tween these two points.
3
Quit the repeat function with »7«.
-30
ENGLISH
usB-operAtion----------------------------------------------------------------------------------------------------------------
image-data
File-formats
Your television can display pictures in the formats
JPEG, PNG and BMP.
Your television can work with the following file
formats using the USB sockets:
JPEG stands for Joint Picture Experts Group.
It denotes a process for compressing picture files.
PNG and BMP are process used to save image
data with no, or very little, losses.
Picture files can be stored with other types of files
on one medium.
These files can be organised into folders and
subfolders.
video-data
Special codecs for video compression and
decompression provide more memory space
without compromising the picture quality exces-
sively.
Your television plays video files in the formats
DIVS, XVID, H.264/MPEG-4 AVC (L4.1, 4 ref-
erence pictures), MPEG-4, MPEG-2, MPEG-1,
MJPEG and MOV.
The following file name extensions are also sup-
ported: AVI, MKV, MP4, TS, MOV, MPG, DAT,
VOB. These files can also contain audio files
compressed using MP3, AAC or Dolby Digital©.
Audio-data
Your television can play audio data in the for-
mats MP3, AAC, WMA.
MP3 is the abbreviation for MPEG-1 Level 3 and
is based on the MPEG-1 standard, which was
developed by the MPEG (Motion Picture Expert
Group).
AAC stands for Advanced Audio Coding and
was also developed by MPEG. AAC provides
better sound quality at an identical data rate.
WMA (Windows Media Audio) is a compres-
sion standard for audio data developed by
Microsoft.
These formats allow audio files to be recorded
and played which sound as good as a CD, while
taking up only a fraction of the memory space.
File name extensions which are supported: MP3,
MP2, WMA, M4A, AAC.
MP3 files can be organised into folders and
subfolders, as on the computer.
-31
ENGLISH
usB-operAtion----------------------------------------------------------------------------------------------------------------
Connecting-external--
data-media-
Before connecting the data medium, switch the
television to standby using »8«. Connect the
device and then switch the television on again.
Before removing the external data medium,
the television set must be switched to standby,
so that no data loss occurs.
notes:
7
If you use a network cable for external hard
disks which are connected to the »usB«
socket on the television, this network cable
must also be disconnected from the power
supply when the television is switched off.
7
External data media may not be disconnect-
1
2
Connect the »usB« socket of the television
and the corresponding socket on the data
device (external hard drive, digital camera,
card reader or MP3 player) using a USB ca-
ble;
ed from the television set while files on the
data medium are being accessed.
7
A bi-directional data transfer as defined for
ITE (Information Technology Equipment)
devices in EN 55022/EN 55024 is not
possible.
or
7
USB transfer is not in itself an operating
mode. It is only an additional function.
insert the USB plug of the USB memory stick
into the »usB« socket of the television set.
Confirm the display »
(green)
– The file browser appears.
« with
»
«
.
-32
ENGLISH
usB-operAtion----------------------------------------------------------------------------------------------------------------
the-file-browser-
The file browser displays video, audio and
picture files stored on external data media.
settings-in-the-usB--
setup-menu
selecting-the-menu
If an external data medium contains files in
different formats, you can, when necessary, filter
out the formats not required.
1
Open the menu with »menu«.
2
Select the »SOURCE SETUP« menu item with
»v
« or »
Λ« and press »oK« to confirm.
main-menu-of-the-file-browser
–
The »USB SETUP« menu appears.
note:
3
1
2
7
Additional functions are explained in the
following sections.
VIDEO FILES
switching-on-automatic-preview
ROOT
Photo
Music
Film
If this function is switched on, a preview of the
selected file then appears in the file browser.
1
2
3
Select the line »Auto Preview« with »
v«
or »Λ«.
USB DRIVE
Used (MB)
Total (MB)
%3
475
45
Switch on the function with » « or » «
<
>
(»On«).
Use Control
Buttons
x1
Speed
All
Repeat
Now
Total
Press »menu« to end the setting.
selecting-the-display-mode
5
4
1
Select »View Mode« with »v« or »Λ«.
1
2
Selected data format.
Total number of folders on the data medium.
2- Select the preferred option with » « or » «.
<
>
3
Press »menu« to end the setting.
3- Preview of the selected file.
setting-the-display-duration-for-
pictures-in-a-slideshow
1
4- Information on the external data medium.
5
Menu navigation.
Select »Slide Show Interval« with »v« or »Λ«.
2
Selectthedisplayduration(3, 5, 10 seconds)
with » « or » «.
<
>
3
Press »menu« to end the setting.
-33
ENGLISH
usB-operAtion----------------------------------------------------------------------------------------------------------------
Divx®-voD
Basic-playback-functions-
You must have your device registered in order to
play the protected video that you will buy from
DivX®.
1
Select the data medium by pressing »
«,
use » «, » «, » « or » « to select the option
v
Λ
<
>
»USB« and press »oK« to confirm.
– The file browser appears.
1
Select »DivX® VOD« with »
confirm with »oK«
– Registration Code appears.
v« or »Λ« and
.
2
3
Select the file format (video files, audio files,
picture files) with » « or » «.
v
Λ
2
3
device with the registration code.
Switch to the folder/file list with »oK«.
note:
Press »menu« to end the setting.
7
USB data medium with several partitions is
connected to the USB sockets, the letter for
the respective drive (e.g. C) appears behind
the folder symbol. Select the letter of the
DivX Certified® to play DivX® and DivX
Plus™ HD (H.264/MKV) video up to
1080p HD including premium content.
drive with »
confirm.
v« or »Λ« and press »oK« to
ABOUT DIVX VIDEO: DivX® is a digital video format created
by DivX, Inc. This is an official DivX Certified® device that plays
DivX video. Visit divx.com for more information and software
tools to convert your files into DivX video.
4
5
Select the folder or file with »v« or »Λ« and
press »oK« to open it.
– A list of subdirectories appears.
ABOUT DIVX VIDEO-ON-DEMAND: This DivX Certified® de-
vice must be registered in order to play purchased DivX Video-
on-Demand (VOD) movies. To obtain your registration code,
locate the DivX VOD section in your device USB setup menu.
Go to vod.divx.com for more information on how to complete
your registration.
note:
7
Switch back to the main folder with » «.
<
Select the track or picture with »
and press »8« to start playing.
You can view information on the film data by
pressing »?«.
v« or »Λ«
–
– When playing MP3 or WMA data, infor-
mation on the album, track and singer is
displayed at the left of the menu.
– When playing picture files, you can use
»?« to display information about the reso-
lution and size.
– When playing picture data, press »
?«
®
twice to enter the DivX Settings menu.
note:
7
When playing picture data, the file browser
7
switches off. Press » « to display the file
browser again.
6
Press »!« to pause playback.
7- Press »8« to resume normal playback.
7
8
Press » « to end playback.
The file browser appears.
-34
ENGLISH
usB-operAtion----------------------------------------------------------------------------------------------------------------
notes:
Additional-playback--
functions
Depending on the file format, the following
additional functions are available:
7
Use »Λ« to select »Up Folder«, when you
would like to return to the last folder. Use
»Root« (and then press »oK«) to return to
the main folder.
selecting-chapters-on-Divx®-files
(only video files)
7
It is possible that files which are actually
supported do not function correctly in USB
mode. This is because certain files are not
recorded with standardised compression
processes, although they feature the “right”
file ending.
1
During playback, select the next chapter
with » «.
>
2
During playback, select the previous
chapter with » «.
<
7
7
7
If a video file features several audio tracks
(audio streams), you can switch these over
during playback in full screen mode with
note:
7
You can also select chapters by entering the
chapter number with »1...0«.
»
«.
When playing music files, you can use other
options in the USB mode at the same time.
This way, you can, for example, enhance a
slideshow with music.
selecting-titles-on-Divx®-files
(only video files)
1
During playback, select the next title with
«.
»Λ
For films, only subtitles in the SRT format
are supported. The names of the subtitle
and film files must be identical. Otherwise,
no subtitles will be shown.
2
During playback, select the previous title
with » «.
v
playing-selected-titles
Only the marked tracks are played.
1
Select the titles with »
»oK« to mark it.
v« or »
Λ
« and press
2
Select the next title with »
v
« or » « and
Λ
press »oK« to mark it.
3
4
Start playback with »8«.
7
Press » « to end playback.
note:
7
To remove the marking, select the title with
« or » « and press »oK« to remove the
marking.
»v
Λ
-35
ENGLISH
usB-operAtion----------------------------------------------------------------------------------------------------------------
selecting-a-track-or-picture-in-steps-
(sKip)
1
During playback, select the next track/
picture with »6«.
2
During playback, select the previous track/
picture with »5«.
– Playback begins with the track or picture
you selected.
selecting-a-certain-passage-for-
playback-
(video files only)
1
2
During playback, press »oK«
Enter the passage (time) with »1-...-0« and
press » « (green) or »oK« to confirm.
.
Fast-forward
(for video and audio files only)
You can select different speeds (2-fold, 4-fold,
8-fold,16-fold and 32-fold forwards and back-
wards).
1
Select the playback speed during playback
with »3« or »4«.
2- Press »8« to resume normal playback.
rotating-pictures-
(picture files only)
You can rotate pictures by 90°.
1
During playback, press » « or « to rotate
the pictures by 90°.
<
>
repeat-functions
Options:
– »One Repeat«: the current track will be
repeated.
– »All Repeat«: all tracks will be repeated.
1
2
Open the Tools menu with »tools«.
Select the menu item »Repeat« with »
v« or
»Λ«.
3- Select »All«, »Random«, »One« or »None«
by pressing » « or » «.
<
>
-36
ENGLISH
teletext-operAtion-----------------------------------------------------------------------------------------------
enlarging-the-character-height
If you have difficulty reading the text on the
screen, you can increase the character height.
top-text-or-FloF-text-mode
1
Press »txt« to switch on teletext.
2
Select teletext pages directly with »1...0«
1
To enlarge the character height of a teletext
page, keep pressing »5«.
or step by step with »v« and »Λ«.
Return to teletext page 100 with »?«.
note:
page-hold
7
At the bottom of the screen there is an info
A multiple page may contain several sub-pages,
which are automatically scrolled by the broad-
casting station.
bar with red, green and – depending on the
channel – yellow and blue panels. Similarly,
the remote control also features buttons with
different colours with which these pages can
be selected.
1
Stop the automatic scrolling of the sub-pages
with »3«.
2- Quit the function with »3«.
3
4
5
Go back a page with » «-(red).
Go to the next page with » « (green).
opening-a-sub-page-directly
Select a particular chapter with
»
«
If the selected teletext page contains additional
pages, the number of the current sub-page and
the total number of pages are displayed.
(yellow)
.
6- Select a particular subject with »
« (blue).
1- Press » « to open the sub-page function.
2- Use » « or » « to select the sub-page.
7
Quit teletext with »txt«.
<
>
normal-text-mode
1
3- Quit the function with » «.
Press »txt« to switch on teletext.
revealing-answers
Certain teletext pages contain hidden answers
or information.
2
Press »1…0« to select teletext pages directly.
Return to teletext page 100 with »?«.
3
4
5
Go back a page with »v«.
1
Display information with »4«.
Go to the next page with »Λ«.
2- Press »4« to conceal the information.
Quit teletext with »txt«.
split-screen
Additional-functions
This functions allows you to display the televi-
sion channel on the left side, the teletext on the
right side.
skipping-the-waiting-time
While a page search is progressing, you can
switch to the TV programme.
1
Switch the function on with »7«.
– The television channel and teletext are dis-
played next to each other.
1
Enter the teletext page number with »1…0«
and then press »6«.
2
Switch the function off with »7«.
– As soon as the page is found, the page
number is displayed.
2
Press »6« to switch to the teletext page.
-37
ENGLISH
ConvenienCe-FunCtions-------------------------------------------------------------------------
Changing-the-audio-language
(only for digital television channels)
opening-the-settinGs-menu
1
Open the menu with »menu«.
You can define a primary and a secondary
audio language.
2
Select the »SETTINGS« menu with »v« or
»
Λ« and press »oK« to confirm.
– The »SETTINGS« menu appears.
1
Select the line »Audio« with »v« or »Λ« and
press »oK« to confirm.
–
The »Select Audio Language« menu
20.09.2010
15:46
appears.
SETTINGS
2
Select the audio language with » «, » «,
<
>
»v« or »
Λ« and then use » «-(red) to set
Language settings
it as the primary audio language, or use
»
« (green) to set it as the secondary audio
Menu
English
English
language.
Audio
Subtitle
– The primary and secondary language is
display at the top right in the menu.
English
Off
Subtitle Mode
Date and time settings
3
Press »menu« to end the setting.
Changing-the-subtitle-language-
and-subtitle-mode
(only for digital television channels)
Date & Time
Time Adjustment
Time Zone
Auto
GMT +1
You can switch the subtitles on and off, select the
subtitle language and allocate a second subtitle
language.
Exit
Back
1
Select the line »Subtitle« with »v« or »Λ«
note:
and press »oK« to confirm.
– The »Select Subtitle Language« menu ap-
pears.
7
Additional operations are explained in the
following sections.
2
Select the subtitle language with »
v«,
language-settings
»Λ«, » « or » «, then use » «-(red) to set
<
>
it as the primary subtitle language, or use
Changing-the-menu-language
»
« (green) to set it as the secondary subti-
1
Select the line »Menu« with »v« or »Λ« and
tle language.
press »oK« to confirm.
– The primary and secondary language is
displayed at the top right in the menu.
–
The »Select Menu Language« menu
appears.
3
4
To go back one menu level, press » «.
<
2- Select the menu language with » «, » «,
<
>
Select the line »Subtitle Mode« with »v« or
»v« or »Λ« and press »oK« to confirm.
»
Λ« and then set the preferred option »Off«,
3
Press »menu« to finish the setting.
»Hard of Hearing« or »Basic« with » « or
<
» «.
>
5
Press »menu« to end the setting.
-38
ENGLISH
ConvenienCe-FunCtions-------------------------------------------------------------------------
setting-the-date-and-time
Automatic-setting
Your television set detects the difference in time
to Greenwich Mean Time (GMT) automatically,
as long as the channel selected transmits a time
signal.
timer-settings
entering-the-switch-off-time--
(sleep-timer)
In the »Sleep Timer« menu you can enter a time
for the television to switch off. After this time
has elapsed, the television switches to standby
mode.
1
2
Select the line »Time Adjustment« with »v«,
1
Select the line »Sleep Timer« with »
»Λ«.
v« or
then select the option »Manual« with » «
<
or » «.
>
– The lines »Time Zone« and »Daylight Sav-
ing« are active.
2
Enter the switch-off time with » « or » «.
<
>
note:
Select the line »Time Zone« with »v« and
7
To switch off the function, use » « or » « to
set the switch-off time to »Off«.
<
>
press »oK« to confirm.
– The »Select Time Zone« menu appears.
3
Press »menu« to end the set-up.
3- Select the appropriate time zone with » «,
<
switch-on-timer
» «, »
v« or »Λ« and press »oK« to con-
>
firm.
In the »Auto On« menu you can enter a switch-on
time for the television. After the preset time has
elapsed, the television switches on from standby
– at the preselected volume and the preselected
television channel.
4
5
Select the line »Daylight Saving« with »
v«
and use » « or » « to set the option »Auto«,
<
>
»Off« or »On«.
Press »menu« to finish the setting.
1
Select the line »Auto On« with
and press »oK« to confirm
»v
« or »
Λ«
.
manual-setting
You can also set the difference in time manually
– for example, when the correct time is not de-
tected automatically or does not correspond to
local time for other reasons
2
Select the line »Mode« with
»
v
« or » and
Λ«
use » « or » « to select when the television
<
>
should switch on.
3
4
Select the line »Input Source« with
»v« or »Λ«
and use » « or » « to select the input source.
1
Select the line »Date & Time« with »
v« or
<
>
»
Λ
« and press »oK« to confirm.
Select the line »Service Type« with
»v« or »Λ«
and use » « or » « to select the preferred op-
2
Select the line »Auto« with »v« or »Λ
« and
<
>
tion (ATV, DTV, Radio or DATA).
Select the line »Channel« with
press »oK« to confirm.
– Date and Time will be updated
automatically;
5
»v« or »Λ«
and use » « or » « to select the preferred
<
>
channel.
or
note:
3
Select the input box with »v« or »Λ«, enter
the data for Date and Time with »1...0«
and press »oK« to confirm.
7
The line »Channel« is only active when the in-
put signal currently in use has been set. If no
entry has been made, then the first channel of
the selected input source will be used.
-39
ENGLISH
ConvenienCe-FunCtions-------------------------------------------------------------------------
6
Select the line »Volume« with
»
v
« or »
Λ
«
and
parental-control-settings
Authorising-programmes
There are films which may be wholly or partially
unsuitable for children.
use » « or » « to set the volume.
<
>
7
Select the line »Set Hour« with
»
v« or »Λ«
and enter the time with »1…0«.
8- Save the data with » « (green).
These programmes contain information which
marks the content or scenes with access levels of
4 to 18. You can select one of the access levels,
thereby authorising playback.
note:
7
You can abort the entry by pressing » «-(red)
.
9
Press »menu« to end the setting.
1
Select the line »Parental Guidance« with
« or » « and press »oK« to confirm.
switch-off-timer
»v
Λ
In the »Auto Off« menu, you can enter a time
for the television to switch off. After this time
has elapsed, the television switches to standby
mode.
2
3
4
Enter the PIN code »1234« with »1-...-0«.
Select the access level with » « or » «.
<
>
Press »menu« to end the setting.
1
2
3
Select the line »Auto Off« with
»
v
« or »
Λ«
locking-menus
and press »oK« to confirm
.
This function allows you to lock the »Automatic
Channel Search«, »Digital Manual Tuning«, »An-
alogue Manual Tuning« and »Program Table«
menus so that they can be only accessed by
entering a PIN code.
Select the line »Mode« with
»
v
« or » and
Λ«
use » « or » « to set the preferred mode.
<
>
Select the line »Set Hour« with
»v« or »Λ«
and enter the time with »1…0«.
4- Save the data with » « (green).
1
2
3
Select »Menu Lock« with »v« or »Λ«.
note:
Enter the PIN code »1234« with »1-...-0«.
7
You can abort the entry by pressing » «-
(red).
Activate the lock with » « or » « (»On«).
<
>
note:
5
Press »menu« to end the setting.
7
To switch off the menu lock, use » « or » «
to select the setting (»Off«).
<
>
Automatic-switch-off-(Auto-sleep)
If this function is activated, the television switches
automatically to standby after 5 minutes if no
video signal is broadcast or in accordance with
the according to European regulations, the tel-
evision switches automatically to standby after 4
hours provided that none of the buttons on the
remote control or on the television is operated
during this period.
4
Press »menu« to end the setting.
locking-keys-(parental-lock)
When the key lock is activated, the buttons on
the television set do not function.
1
Select the line »Keypad Lock« with »
«.
v« or
»Λ
2
Enter the PIN code »1234« with »1-...-0«.
1
Select the line »Auto Sleep« with »
v« or
3- Activate (On) or deactivate (Off) the key lock
»Λ«.
with » « or » «.
<
>
2
Activate the function with » « or » «
<
>
4
Press »menu« to end the setting.
(»On«).
note:
7
To switch off the function, use » « or » « to
<
>
select the setting »Off«.
3
Press »menu« to end the setting.
-40
ENGLISH
ConvenienCe-FunCtions-------------------------------------------------------------------------
Changing-the-pin-code
updating-software
You can also enter a personal PIN code instead
of the default code »1234«. Please take note of
your own PIN code.
(for digital channels only)
1
In the »SETTINGS« menu, select the line
»Check For Updates updates« with » « or
« and press »oK« to confirm.
v
1
2
3
4
5
Select »Set PIN« with »v« or »Λ« and press
»Λ
»oK« to confirm.
– A search for new software will be made
and – if available – it will be installed.
Enter the current PIN code 1 2 3 4 with
»1...0«.
note:
7
If a search for software updates should be
Enter your new four digit PIN code with
»1...0«.
made automatically, select the line »Auto-
matic OAD« with »v« or »Λ« and use » «
<
Enter your new four digit PIN code with
»1...0« again.
or » « to select the option »On«.
>
– The software will be updated automati-
cally as far as possible.
Press »menu« to end the setting.
2
Press »menu« to end the setting.
locking-television-channels-
You can lock individual television channels, for
example channels unsuitable for children, using
a personal PIN code.
restoring-the-television-to-the-
default-settings
This function allows you to delete the channel
lists and all custom settings.
1
2
Open the menu with »menu«.
Select the »SOURCE SETUP« menu with »
or »Λ« and press »oK« to confirm.
v«
1
2
3
In the »SETTINGS« menu, select the line
»Restore Factory Defaults« with »v« or »Λ«
3
Select the line »Program Table« with »
v« or
and press »oK« to confirm.
»Λ« and press »oK« to confirm.
Press » « (green) to confirm the warning
– The »PROGRAM TABLE« menu is dis-
played.
message.
– The »Source Setup« menu appears.
4
5
6
7
In the »PROGRAM TABLE« menu, switch
Continue the settings with the chapter “Initial
set-up and tuning television channels” on
page 14.
over to the list view with » « (yellow).
Select the channel to be locked with »
v«
or »Λ«.
Select the column »Lock« with » « or » «
<
>
and press »oK« to lock the channel.
Enter the PIN code »1234« with »1-...-0«.
– The channel is marked using »✔«.
note:
7
To remove the lock, select the channel again
with »v« or »Λ«, press »oK« to confirm
and then enter the PIN code 1 2 3 4 using
»1-...-0«.
8
Press »menu« to end the setting.
-41
ENGLISH
operAtion-usinG-externAl-DeviCes------------------------------
searching-for-and-activating--
external-devices
You can connect up to 11 devices with DIGI LINK
functions to your television.
DiGi-linK
Your television is equipped with
the DIGI LINK function.
This function uses the CEC
(Consumer Electronics Control)
protocol.
1
Open the CEC device list with »CeC«.
– The »HDMI CEC Device List« appears.
CEC allows external devices which are connect-
ed to the »hDmi« sockets by an HDMI cable
(e.g. DVD player) to be operated with a remote
control.
Prerequisite is that the devices connected support
CEC. Read the operating manual for the external
device to find out how to activate the correspond-
ing function.
2
Start the device search with » «-(red).
The devices found are displayed in the
menu.
–
3- Select the device for operation with »
v«,
»
Λ
«, » « or » « and press »oK« to mark it.
<
>
– If the selected device is connected to a
different input to the current one, a switch
to the respective input will occur auto-
matically.
the-DiGi-linK-functions-on-your-
television
4
Press »menu« to end the setting.
switching-on-the-television--
automatically-from-standby
If the »Autom. switch-on TV« function is activated
(»On«), then once the external device (e.g.
DVD player) is switched on, the television also
switches on and the appropriate HDMI preset is
selected.
Automatic-selection-of-the-hDmi-
preset-on-the-television
If your television is switched on and you then
switch on the external device (e.g. DVD player),
the appropriate HDMI preset on the television
will be selected.
selecting-the-menu-language
The television menu language is automatically
selected on the external device (e.g. DVD player).
The external device must support this function.
switching-off-the-external-device-
automatically
If you switch your television to standby, the ex-
ternal device (if it is switched on) will also be
switched to standby.
DIGI LINK is always active on your television set.
-42
ENGLISH
operAtion-usinG-externAl-DeviCes------------------------------
switching-the-device-to-standby
This option switches the external device to
standby.
Device-operation
You can decide whether external devices should
react to your television's remote control.
1
Press »
«, use »v«, »Λ«, » « or » « to
1
Press »
«, use »v«, »Λ«, » « or » « to
<
>
<
>
select the preset »HDMI1« to »HDMI3« and
press »oK« to confirm.
select the preset »HDMI1« to »HDMI3« and
press »oK« to confirm.
2
3
Open the menu with »menu«.
Select the menu item »SOURCE SETUP« with
2
3
Open the menu with »menu«.
Select the menu item »SOURCE SETUP« with
»
v« or »Λ« and press »oK« to confirm.
»
v« or »Λ« and press »oK« to confirm.
– The »SOURCE SETUP« menu appears.
– The »SOURCE SETUP« menu appears.
4
Select »Device Standby« with »v« or »Λ«
20.09.2010
15:46
and press »oK« to confirm.
SOURCE SETUP
– The external device switches itself off.
Source
HDMI1
DIGILINK
GRUNDIG DVD
RC Passthrough
Device Selection
Remote Control
Device Standby
Exit
Back
4
Select the line »Remote Control« with »
or » «.
v«
Λ
5- Select the type of operation (»RC Pass-
through«, »Deck« or »Tuner« with » « or
<
» «.
>
notes:
7
»RC Passthrough« can be used for all devices.
»Deck« and »Tuner« can be selected in ac-
cordance with the external device which
has been connected.
7
Try out which type of remote control opera-
tion the external device reacts to the best.
7
Read about the scope of functions of the
DIGILINK-compatible device in the respec-
tive operating manual.
6
Press »menu« to end the setting.
-43
ENGLISH
operAtion-usinG-externAl-DeviCes------------------------------
high-definition--hD-ready
Connection-options
7
Which television socket(s) you connect your
Connect the corre-
external devices to depends on the sockets
the external device is equipped with and the
signals which are available.
sponding input sources
(e.g. HDTV receiver or
HD-DVD player) to the
»hDmi« sockets (for
digital HDTV sources).
7
Please note: With many external devices,
the resolution of the video signal must be
adjusted to the input sockets of the television
(see the operating manual of the external
device). You can find out which values you
need to set by referring to the guidelines in
the sections about the various connection
options.
This ensures that you can view digital HDTV
programmes, even if they are copy-protected
(HDCP High Bandwidth Digital Content Protec-
tion), without encountering problems.
7
Do not connect any other equipment while
the device is switched on. Also switch off the
other equipment before connecting it.
7
Do not plug in the power cord of the device
until you have connected the external equip-
ment and the antenna.
-44
ENGLISH
operAtion-usinG-externAl-DeviCes------------------------------
...-using-the-sCArt-socket--
(CvBs/rGB-signal)
Connecting-external-devices
...-with-digital-audio/video-signals
7
Suitable devices: Digital satellite receiver,
7
Suitable devices: Digital satellite receivers,
DVD player/recorder, set-top box, games con-
sole, video recorder, decoder.
Video signal: CVBS/RGB.
Audio signal: stereo, analogue.
»AV1« preset.
Playstation, BluRay player, DVD player/
recorder, set-top box, notebook, PCs.
Video signal: Digital video; resolution: stand-
7
7
7
ard 576p; HDTV 720p, 1080i, 1080p.
Audio signal: digital audio (stereo, multi-chan-
7
7
1
Connect the »Av1/s-vhs« socket on the
television and the corresponding socket on
the external device using a SCART cable
(video and audio signal).
nel compression, uncompressed).
Presets »HDMI 1«, »HDMI 2« or »HDMI3«.
7
1
Connect
the »hDmi1«, »hDmi2«,
» hDmi3« socket on the television and the
corresponding HDMI socket on the external
device using a standard HDMI cable (digital
video and audio signal).
Activating-a-decoder
If a decoder is connected to the »Av1/s-vhs«
socket, this must be activated to provide an
unencrypted video/audio signal.
...-with-analogue-video-signal-
(progressive)
1
2
Open the menu with »menu«.
Select »SETTINGS« with »v« or »Λ« and
press »oK« to confirm.
– The »SETTINGS« menu appears.
7
Suitable devices: DVD recorders/players,
games consoles.
Video signal: YUV; resolution: standard 576p;
7
HDTV 720p, 1080i, 1080p.
Audio signal: stereo, analogue.
»Component« preset.
3
4
Select the »Decoder« with »
v« or »Λ«.
7
Activate the function with » « or » «
(»On«).
Press »menu« to end the setting.
<
>
7
1
2
Connect the »Component- Y/Av2- pb-
pr« sockets on the television to the corre-
sponding sockets of the external device with
RCA cables (video signal).
5
...-with-s-video-signal
7
Suitable devices: DVD player/recorder, video
recorder, camera recorder, notebook, PC.
Video signal: Y/C.
Audio signal: stereo, analogue.
»S-VHS« preset.
Connect the »Component-l-r« sockets
on the television to the corresponding sock-
ets of the external device with RCA cables
(audio signal).
7
7
7
1- Connect the » Av1/s-vhs« socket on the
television and the corresponding socket on
the external device using an EURO/AV ca-
ble (video and audio signal).
-45
ENGLISH
operAtion-usinG-externAl-DeviCes------------------------------
...-with-an-analogue-tv-signal
using-a-DvD-player,-
DvD--recorder,-video-recorder--
or-set-top-box
7
Suitable devices: Digital satellite receiver,
DVD player/recorder, set-top box, camera
recorder.
Video signal: CVBS.
Audio signal: stereo, analogue.
»AV2« preset.
1
Switch on the external device and select the
function you wish to use.
7
7
2
Press
»
«, use »v«, »Λ«, » « or » « to
7
<
>
select the preset for the input signal (»AV1«,
»AV2«, »S-VHS«, »HDMI1«, »HDMI2«,
»HDMI3« or »Component«) and press
»oK« to confirm.
1
2
Connect the »Y/Av2« socket on the
television to the corresponding socket of the
external device with an RCA cable (video
signal).
Connect the »l--r« sockets on the television
to the corresponding sockets of the external
device with RCA cables (audio signal).
headphones
Connecting-the-headphones
1
Plug the headphone jack (3.5 mm ø jack
plug) into the headphone socket on the left
side of the television.
Changing-the-headphone-volume
1
Open the menu with »menu«.
2
Select the menu item »SOUND SETTINGS«
with »v« or »Λ« and press »oK« to confirm.
– The »SOUND SETTINGS« menu appears.
3
4
Select the menu item »Audio Output Setup«
with »
v« or »Λ« and press »oK« to confirm.
– The »Audio Output Setup« menu appears.
Select the line »Headphone« with » « or
v
»Λ«.
5
6
Set the preferred volume with » « and » «.
<
>
Press »menu« to end the setting.
note:
7
Prolonged listening with headphones at loud
volumes can damage your hearing.
-46
ENGLISH
operAtion-usinG-externAl-DeviCes------------------------------
playing-the-audio-signal-via-the--
hiFi-system
1- Connect the »U« sockets on the television to
the corresponding socket of the AV receiver
with an cable (digital audio signal).
hi-fi-system/Av-receiver
Connecting-the-hi-fi-system/-
Av-receiver
1- Connect the »optic- out« socket on the
television to the corresponding socket of the
device with an optical digital cable (digital
audio signal).
note:
7
If this function is not activated, the audio sig-
nal is transmitted to the HiFi system/AV re-
ceiver (connected to »U« 3.5 mm ø jack
plug) into the headphone socket on the left
side of the television.
setting-the-audio-format
You can select whether the audio signal output
via the »optic-out« socket should be in the
PCM or AC2 format.
1
2
Open the menu with »menu«.
1
2
Open the menu with »menu«.
Select the menu item »SOUND SETTINGS«
with »v« or »Λ« and press »oK« to confirm.
Select the menu item »SOUND SETTINGS«
– The »SOUND SETTINGS« menu appears.
with »v« or »Λ« and press »oK« to confirm.
– The »SOUND SETTINGS« menu appears.
3
4
5
Select »Audio Output Setup« with » « or
v
»
Λ« and press »oK« to confirm.
3
Select »Audio Output Setup« with » « or
v
– The menu appears.
»
Λ« and press »oK« to confirm.
– The menu appears.
Select the line »Audio Out« with »v« or »Λ«
and press » « or » « to activate the audio
4
5
Select the »Optic Out« with »v« or »Λ«.
<
>
output (»Line Out«).
Select the line » Audio Out Status« with »
or » « and select the option »Fixed« or »Ad-
justable« with » « or » «.
Select the preferred audio format (»PCM« or
»Auto«) with » « or » «.
v«
<
>
Λ
note:
<
>
7
If you wish to output the audio only via a
multi-channel amplifier/AV receiver, set the
option »TV Speaker« to »Off« in the menu.
notes:
7
If you select »Adjustable«, the volume can
be changed in the menu option » Audio Out
Volume«.
6
Press »menu« to end the setting.
7
If the audio should only be output via the
HiFi system/AV receiver, select the option
»Off« in the line »TV Speaker with » « or
<
» «.
>
6
Press »menu« to end the setting.
“Dolby” and the double-D logo are trademarks of
Dolby Laboratories.
Manufactured under licence from Dolby Laboratories.
-47
ENGLISH
operAtion-As-A-pC-monitor-----------------------------------------------------------
Connecting-a-pC
20.09.2010
15:46
1
Connect the »pC-in« socket on the television
to the corresponding socket on the PC using
a VGA cable (video signal).
SOURCE SETUP
2
Connect the »Audio« socket on the televi-
sion to the corresponding socket on the PC
using a suitable cable (audio signal).
Source
PC
Auto Ajust
Extended settings
note:
Auto Ajust Mode
On
50H - 50V
0
7
Adjust your PC to the monitor (for example,
picture resolution 1280 x 768, picture fre-
quency 60 Hz).
Position
Size
Phase
30
selecting-presets-for-the-pC
1
Press »
« and use »v«, »Λ«, » « or » «
<
>
Exit
Back
to select the preset »PC« and press »oK« to
confirm.
Options:
settings-for-pC-mode
–
»Auto Ajust« for automatic PC configura-
tion.
1
Open the menu with »menu«.
– »Auto Ajust Mode«, select the option
»On« if the configuration should be imple-
mented automatically in PC mode.
– »Position« to configure the horizontal and
vertical picture position.
– »Size« to set the cycle frequency.
– »Phase« to eliminate flicker, unfocused
pictures or horizontal interference.
2
Select the »SOURCE SETUP« menu item with
»
v« or »Λ« and press »oK« to confirm.
– The »SOURCE SETUP« menu appears.
3- Select the function or setting with » « or
« or » «, » « to
v
»
Λ«, and then use »v«, »Λ
<
>
implement it.
4
Press »menu« to end the setting.
-48
ENGLISH
operAtion-with-A-Common-interFACe-------------------
what-is-a-Common-interface?
Access-control-for-Ci-module-and-
smart-card
7
Common Interface (CI) is an interface for
DVB receivers.
Encrypted channels can only be viewed
1
Open the menu with »menu«.
7
2
Select the line »SOURCE SETUP« with »
or »Λ« and press »oK« to confirm.
v«
with a CA module suitable for the encryp-
tion system and in conjunction with the
corresponding smart card.
The television set is equipped with a Com-
mon Interface slot into which CI modules
from various providers can be inserted.
You can insert the provider’s smart card into
the CA module in order to enable the en-
crypted channels you wish to view.
– The »SOURCE SETUP« menu appears.
Select the line »CA-Module« with » « or
« and press »oK« to confirm.
7
3
v
»
Λ
notes:
7
7
This menu provides operating instructions
and – after you enter your PIN code – ac-
cess to the PAY-TV provider's channels.
inserting-the-CA-module
note:
7
7
The remaining settings are described in the
operating manuals for your CI module and
smart card.
7
Switch the device off before you insert a CA
module into the »Ci« slot.
The CA modul is not supported in certain
countries and regions; please consult your
authorised dealer.
1
2
Insert the corresponding smart card into the
CI module.
Insert the CI module with the smart card into
the »Ci« slot on the television.
4
Press »menu« to end the setting.
note:
7
In the »CA Module« sub-menu you can see
which CA module has been inserted in the
CI slot.
7
If you are inserting a CA module into the
CI slot of the television for the first time, you
will need to wait a moment until the CA mod-
ule is detected.
-49
ENGLISH
speCiAl-settinGs-----------------------------------------------------------------------------------------------------------
note:
searching-for-television-chan-
7
You can accelerate the search. To do this,
you need information about the frequency
and network ID. You are usually able to get
this data from your cable operator or find it
in forums on the Internet. For example, the
frequency 402MHz and network ID 61441
can be entered for Germany.
nels-from-the-cable-provider-
automatically
1
Open the menu with »menu«.
2
Select the line »SOURCE SETUP« with »
or »Λ« and press »oK« to confirm.
v
«
«
– The »SOURCE SETUP« menu appears.
Select the line »Source« with
or » « and press »oK« to confirm.
Select the option »Cable« with » «, » «,
7
Start the scan with » «-(red).
– All channel and favourites lists will be
deleted and compiled anew.
3
4
»
v
Λ
<
>
»v
« or »
Select the line »Automatic Channel Search«
with » « or » « and press »oK« to confirm.
– The menu appears.
Λ« and press »oK« to confirm.
note:
7
After starting the scan, a security query will
appear. Press » « (green) to confirm the
v
Λ
option »Yes«.
– The »Results« menu appears, and the scan
for TV channels begins. Depending on the
number of television channels received,
this can easily take a few minutes.
20.09.2010
15:46
SOURCE SETUP
AUTOMATIC CHANNEL SEARCH
– The scan is complete as soon as the »PRO-
GRAM TABLE« appears.
Connection Type
Cabel
U.K.
Country
note:
ATV & DTV
Quick
Scan Type
7
You can abort the search by pressing
»menu«.
Cable Scan Type
Frequency (MHz)
Network ID
Auto
8
Press »menu« to end the setting.
Auto
Exit
Back
Start Search
5
6
Select the line »Scan Typ« with »
v
« or »
Λ
«
and set the option »DTV« with » « or » «.
<
>
Select the line »Cable Scan Type« with »
or »
with » « or » «.
v«
Λ« and set the option »Quick« or »Full«
<
>
– The search function »Quick« sets the channels
according to the information provided by your
cable provide in the transmission signal.
– If the option »Full« is selected, the entire fre-
quency range will be scanned. The search
can take a long time with this option. This op-
tion is recommended if your cable provider
does not support the search type »Quick«
.
-50
ENGLISH
speCiAl-settinGs-----------------------------------------------------------------------------------------------------------
searching-for-television-channels- searching-for-digital-terrestrial-
from-the-cable-provider-manu-
ally
tv-channels-automatically
1
Open the menu with »menu«.
1
Open the menu with »menu«.
2
Select the line »SOURCE SETUP« with »
v
«
«
or »Λ« and press »oK« to confirm.
2
Select the line »SOURCE SETUP« with »
v
«
«
– The »SOURCE SETUP« menu appears.
Select the line »Source« with
or » « and press »oK« to confirm.
Select the option »Air« with » «, » «, »
or »Λ« and press »oK« to confirm.
– The »SOURCE SETUP« menu appears.
3
»
v
Λ
3
Select the line »Source« with »v« or »
Λ
v« or
and press »oK« to confirm.
<
>
»
Λ« and press »oK« to confirm.
Select the option »Cable« with » «, » «,
<
>
»v« or »Λ« and press »oK« to confirm.
Caution:
4
5
Select » Digital Manual Tuning« with »
v
« or
7
The antenna power supply (line »Active
Antenna Power«) may only be switched on
if the antenna is an active indoor antenna
with a signal amplifier and it is not already
supplied with a voltage via a mains plug
(or similar supply). Otherwise you may
cause a short circuit and irreparably dam-
age your antenna.
»
Λ
« and press »oK« to confirm.
– The menu appears.
Enter the four-digit frequency with »1-...-0«
and press »oK« to confirm.
–
The search starts after confirming, the
channels found are displayed in the »Re-
sults« menu.
4
5
Select the »Active Antenna Power« with »
or » «. Switch on the antenna power supply
for the antenna with » « or » « (»On«).
v«
6
Press »menu« to finish the setting.
Λ
<
>
Select the line »Automatic Channel Search«
with »v« or »Λ« and press »oK« to confirm.
– The menu appears.
20.09.2010
15:46
SOURCE SETUP
AUTOMATIC CHANNEL SEARCH
Connection Type
Air
U.K.
Country
ATV & DTV
Scan Type
Exit
Back
Start Search
-51
ENGLISH
speCiAl-settinGs-----------------------------------------------------------------------------------------------------------
6
Select the line »Scan Typ« with »
v« or »Λ«
searching-for-digital-terrestrial-
tv-channels-manually
and set the option »DTV« with » « or » «.
<
>
7
Start the scan with » «-(red).
1
Open the menu with »menu«.
– All channel and favourites lists will be
deleted and compiled anew.
2
Select the line »SOURCE SETUP« with »
v
«
«
or »Λ« and press »oK« to confirm.
note:
– The »SOURCE SETUP« menu appears.
7
After starting the scan, a security query will
3
Select the line »Source« with »v« or »
Λ
appear. Press » « (green) to confirm the
and press »oK« to confirm.
option »Yes«.
Select the option »Air« with » «, » «, »v« or
<
>
– The »Reults« menu appears, and the scan
for TV channels begins. Depending on the
number of television channels received,
this can easily take a few minutes.
– The scan is complete as soon as the
»PROGRAM TABLE« appears.
»Λ
« and press »oK« to confirm.
Caution:
7
The antenna power supply (line »Active
Antenna Power«) may only be switched on
if the antenna is an active indoor antenna
with a signal amplifier and it is not already
supplied with a voltage via a mains plug
(or similar supply). Otherwise you may
cause a short circuit and irreparably dam-
age your antenna.
note:
7
You can abort the search by pressing
»menu«.
8
Press »menu« to end the setting.
4
5
6
Select the »Active Antenna Power«« with »
or » «. Switch on the antenna power supply
for the antenna with » « or » « (»On«).
v«
Automatic-service-update-
If this function is activated, possible changes of
network operators are updated automatically.
Λ
<
>
Select » Digital Manual Tuning« with »
« and press »oK« to confirm.
– The menu appears.
v« or
The unit must be located in stand-by mode.
»Λ
1
2
Open the menu with »menu«.
Select the line »SOURCE SETUP
or » « and press »oK« to confirm.
Select the line »Automatic Service Update«
with » « or » «.
Enter the channel number directly with
1-...-0« and press »oK« to confirm.
«
with »v«
»
Λ
–After the search is complete, the channels
found are displayed in the »Results« menu.
3
4
5
v
Λ
7
Press »menu« to finish the setting.
Select the automatic update with » « or » «
(»On«).
<
>
Press »menu« to end setting.
-52
ENGLISH
speCiAl-settinGs-----------------------------------------------------------------------------------------------------------
5
Select the line »Scan Typ« with »
v« or »Λ«
tuning-analogue-television-
-channels
This setting is only necessary if you cannot re-
ceive any digital channels and you have not car-
ried out an analogue search during initial setup.
The television channels can be set directly or
using the scan.
and set the option »ATV« with » « or » «.
<
>
6
Start the scan with » «-(red).
note:
7
After starting the scan, a security query will
appear. Press » « (green) to confirm the
option »Yes«.
– All channel and favourites lists for the ana-
logue channels will be deleted and com-
piled anew.
setting-all-analogue-television-
channels
– The »Results« menu appears, and the scan
for TV channels begins. Depending on the
number of television channels received,
this can easily take a few minutes.
– The search is complete as soon as the »PRO-
GRAM TABLE« appears.
Analogue channels are displayed in the channel
list after the digital channels.
note:
7
Plug the rooftop antenna cable (for analogue
television channels) into the »Ant-in«
socket on the television.
note:
1
2
Open the menu with »menu«.
7
You can abort the search by pressing
»menu«.
Select the line »SOURCE SETUP« with »
v
«
«
or »Λ« and press »oK« to confirm.
7
Press »menu« to end the setting.
– The »SOURCE SETUP« menu appears.
3
4
Select the line »Source« with »v« or »
Λ
and press »oK« to confirm.
Select the option »Air« or »Cable« with » «,
<
» «, »
v« or »Λ« and press »oK« to con-
>
firm.
Select the line »Automatic Channel Search«
with »
v« or »
Λ« and press »oK« to confirm.
20.09.2010
15:46
SOURECE SETUP
Source
Air
OK
Automativ Channel Search
Digital Manual Tuning
Analogue Manual Tuning
Program Table
Signal Information
Automatic Service Update
On
CA - Modul
Not inserted
Off
Active Antenna Power
Exit
Back
-53
ENGLISH
speCiAl-settinGs-----------------------------------------------------------------------------------------------------------
tuning-the-television-channels-by-
entering-the-channel-numbers
Changing-stored-analogue-
-channels
If channels were stored with the automatic chan-
nel search while tuning the television channels,
you can delete them. You can also store chan-
nels in a different preset, change or enter the
name of a channel as well as skip channels.
1
Open the menu with »menu«.
2
Select the line »SOURCE SETUP« with »
v«
or »Λ« and press »oK« to confirm.
– The »SOURCE SETUP« menu appears.
3
Select the line » Analogue Manual Tuning«
with »v« or »Λ« and press »oK« to confirm.
selecting-a-channel-list
– The menu appears.
1
Open the menu with »menu«.
2
Select the line »SOURCE SETUP« with »
v«
INSTALLATION
ANALOGUE MANUAL TUNING
or »Λ« and press »oK« to confirm.
– The »SOURCE SETUP« menu appears.
Program No
TSystem
Band
1
BG
C
3
Select the line »Program Table« with » « or
v
»
Λ« and press »oK« to confirm.
– The »PROGRAME TABLE« menu appears.
note:
Channel
2
7
Additional operations are explained in the
following sections.
Fine Tuning
0
48.25 MHz
Deleting-channels
1
In the »PROGRAME TABLE« menu, select the
television channel to be deleted with «,
«, » « or » « and press » «-(red) to con-
Auto Previous
Auto Next
Store
»v
»
Λ
firm.
<
>
4
5
Select the line »Program No« by pressing »
or » « and use » « or » « to save the preset.
Select »Band« by pressing »
use »» « or » « to choose between »S«
v«
Λ
<
>
2
Press » « (yellow) to confirm the deletion
v
« or »
(special channel) or »C« (normal channel).
Select the line »Channel« with » « or » « and
Λ« and
process.
<
>
note:
7
»
« (blue) allows all television channels
6
v
<
Λ
>
enter the channel number with » « or » « step
by step, or use »1…0« to enter it directly.
to be deleted.
3
Press » « (green) to confirm the deletion
notes:
process.
7
The current system is displayed in the
»System« line. If the colour or sound is
not functioning properly, select the line
»System« with »v« or »Λ«. Use » « or » «
<
>
to select the preferred setting.
7
If fine tuning is necessary, select the line
»Fine Tuning« with » « or » « and use » «
or » « to make the setting.
v
Λ
<
>
7
Press » « (blue) to save the setting.
note:
7
If you wish to remedy other television
channels, repeat steps 4 to 8.
8- Press »menu« to end the setting.
-54
ENGLISH
speCiAl-settinGs-----------------------------------------------------------------------------------------------------------
entering-channel-names-(8-digit-
maximum)
Creating-lists-of-favourites
You can select your favourite channels and
save them in up to four favourites lists (Fav 1 to
Fav 4).
1
In the »PROGRAME TABLE« menu, select the
television channel with » «, » «, » « or
» « and press » «-(red) to confirm.
v
Λ
<
>
1
2
3
In the »PROGRAME TABLE« menu, switch
over to the list view with » « (yellow).
2
Open the input keyboard with » « (green).
Select the preferred channel with »
or »Λ«.
v«
note:
7
If necessary, delete the current channel
name. To do this, select the »
« button
Use » « or » « to ”push“ the channel into
<
>
with » « or » « and delete repeatedly using
one of the favourites lists 1 to 4 and press
»oK« to confirm.
<
>
»oK«
Select the required letters or numbers with
«, » «, » « or » « and confirm with
»oK«
.
– The position in the favourites list is marked
with »✔«.
– You can enter the same channel in more
than one favourite list.
– Eachfavouritelistcanstoreupto255 chan-
nels.
3
4
»
v
Λ
<
>
.
Repeat the entry for further letters/numbers.
note:
7
Use the »ABC« button to switch to upper
note:
case letters and use the »?@123« button to
switch to symbols and numbers.
7
Channels can also be deleted from favour-
ites lists. Select the channel to be deleted
with »
v«, »Λ«, » « or » « and delete it with
Save the channel name by using »v«, »Λ«,
<
>
»oK«
.
» « or » « to select »Submit« and confirm
<
>
with »oK«
.
exiting-the-settings
Press »menu« to end the setting.
note:
1
7
If you wish to enter other channel names,
repeat steps 1 to 4.
skipping-television-channels
You can highlight television channels to be
skipped when you select with »Λ« or »v«.
Selection is still possible using the number
buttons.
1
2
3
In the »PROGRAMETABLE« menu, switch over
to the list view with » « (yellow).
Select the preferred channel with »
v«
or »Λ«.
Select the column »Skip« with » « or » «
<
>
and use »oK« to mark the channel.
– The channel is marked using »✔«.
note:
7
Channels can also be reactivated. Select the
channel with » « or » «, then select the
column »Skip« and reactivate the channel
with »oK«
v
Λ
.
-55
ENGLISH
inFormAtion----------------------------------------------------------------------------------------------------------------------
Displaying-signal-information
(for digital channels only)
service-information-for-retailers
Only operate the television
with the power supply/power
cord provided.
The product complies with the
1
2
Open the menu with »menu«.
Select the line »SOURCE SETUP« with »
or »Λ« and press »oK« to confirm.
v«
following EU directives:
2006/95/EC directive on electrical equipment
for use within certain voltage limits.
2004/108/EC directive on electromagnetic
compatibility.
2009/125/EC directive on ecodesign require-
ments for energy-related products.
Power consumption values and classes are speci-
fied according to the regulations 2009/642 and
2010/1062 and the standards EN62087 and
EN62301 as per European Union framework di-
rectives 2009/125/EC and 2010/30/EU
3
Select the line »Signal Information« with
« or » « and press »oK« to confirm.
– Information on the channel, network,
modulation, symbol rate, quality and
signal strength is displayed.
»v
Λ
notes:
7
The signal information changes in accord-
ance with the current input source.
7
The signal properties are displayed in the
lower section of the menu. The further the
bars for »Quality« and »Signal Strenght«
extend to the right, the better the reception
signal.
environmental-note
This product has been made
from high-quality parts and
7
The signal level not only depends on your
receiver system, but also on the channel
which is currently active. Remember this
when aligning your antenna based upon
the signal level display.
materials which can be re-used
and recycled.
Therefore, do not dispose of the
product along with normal household waste at
the end of its service life. Take it to a collection
point for the recycling of electrical and electronic
equipment. Dispose of the used device at a collec-
tion point for electrical and electronic equipment.
The symbol on the product, in the operating man-
ual or on the packaging indicates that recycling
is possible.
4
Press »menu« to close the menu.
Information on collection points is available from
your local authorities.
Help protect the environment by recycling used
products.
-56
ENGLISH
inFormAtion----------------------------------------------------------------------------------------------------------------------
Analogue-reception-ranges:
C02 ... C80, special channels S01 ... S41
GrunDiG-32-vlC-6121-C
technical-data
preset-channels:-
operating-voltage:-
TV/Radio
1000 (Cable – DVB-C) or
100 (Analogue)
1000 (Terrestrial – DVB-T) or
100 (Analogue)
8 AV, 1 USB
220–240 V, , 50–60 Hz
~
power-consumption:
On mode 83 W
Standby < 0,50 W
screen-(dm²):
28 dm²
screen-size:
80 cm/32 inch
energy-efficiency-class:
C
maximum-power-consumption
Operational 145 W
maximum-resolution:
WUXGA, 1920 x 1080
Annual-power-consumption
121 kWh
weight:
approx. 12 kg
Audio-output:-
2 x 20 W music power output
2 x 10 W Sine wave power
Dimensions:
W H D 79,5 cm 54,5 cm 8,1 cm
rohs-limits: Pb (Lead)/Hg (Mercury)
Pb meets ROHS directive / 56 mg
peak-luminance-ratio:
% 65
Digital-reception-ranges
Cable:
Overall band: 110 MHz – 862 MHz
Modulation:
16QAM, 32QAM, 64QAM,
128QAM and 256QAM
Symbol rate: 4.0 Msym/s to 7.0 Msym/s
terrestrial:
VHF/UHF band, Bandwidth 7 MHz
and 8 MHz
COFDM modi: 2k and 8k
Constellation: 16QAM, 64QAM, QPSK
terrestrial-(DvB-t2):
VHF/UHF band, Bandwidth 7 MHz
and 8 MHz
FFT Size:
Modulation:
1k, 2k, 4k, 8k, 16k, 32k
16QAM, 64QAM,
256QAM, QPSK
Guard Interval: 1/4, 19/256, 1/8, 19/128,
1/16, 1/32, 1/128
As this feature is optional, it is not available in
all products.
Technical changes and errors reserved.
-57
ENGLISH
inFormAtion----------------------------------------------------------------------------------------------------------------------
troubleshooting
If the information provided below does not help, please consult an authorised GRUNDIG dealer.
Please bear in mind that malfunctions can also be caused by external devices such as video recorders
or satellite receivers.
problem
possible-cause
remedy
Screen lit (snow), but no
station visible
Antenna cable
Is the antenna cable connected?
No TV channel tuned
Start a channel scan
Insufficient contrast in picture
The picture settings are not correct
Adjust the brightness, contrast or
colour setting
Problem at station
Try another channel
Picture and/or sound distorted Interference from other devices
Place the device in a different position
Ghosting, reflection
No colour
Channel setting
Antenna
Automatic or manual tuning/fine tuning
Have antenna cable or system checked
Turn up the colour
Colour intensity too low
Adjust TV standard (if setting option
is available)
Select the correct colour standard
Problem at station
Try a different channel
Picture but no sound
Volume is set to a minimum
Turn up or switch on the volume
Teletext impaired or absent
Problem at station
Try a different channel
Television channel (no teletext)
or antenna system
Try with a different TV channel,
carry out fine tuning
Station signal too weak
Check antenna
The remote control does
not work
Obstacle between remote control
and device.
Point remote control at television
Battery problem
Check batteries and replace if
necessary
Operating mode undefined
Switch off the television at the mains
switch for two minutes
Picture too dark in PC mode
Incorrect setting for picture resolution Change settings on the PC
and picture frequency on the PC
(e.g. 1280 x 768 resolution,
refresh rate 60 Hz)
note:
7
This is a Class A product. During operation the device could cause radio interference. In this case
the user may have to remedy this. Please contact your specialist dealer.
-58
ENGLISH
|
GSI Outdoors Ventilation Hood PNEG 524 User Manual
Haier Refrigerator PBFS21 User Manual
Haier Washer Dryer HWDC1000TXVE ME U User Manual
Haier Washer XPM20 A User Manual
Harbor Freight Tools Nail Gun 98917 User Manual
Harbor Freight Tools Paint Sprayer 97855 User Manual
Hotpoint Cooktop EG74 User Manual
Hotpoint Electric Pressure Cooker GW32 User Manual
Hotpoint Washer WM61 User Manual
Husqvarna Chainsaw 3120XP User Manual